Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18

Thread: Drill press into milling machine

  1. #1
    mariusmarius's Avatar
    Join Date
    Apr 2015
    Location
    Romania, Buzău County
    Posts
    8
    Thanks
    12
    Thanked 3 Times in 3 Posts

    Drill press into milling machine

    Hi everyone!
    I have a small garage to spend my free time in afternoons. I have decided to use a common desk drill press and to transform it into milling maschine. I have read a lot of articles on internet about it.
    If you have any ideas about this topic, please feel free and send them to me.
    Thanks.
    Marius

    186 More Best Homemade Tools eBook

  2. The Following User Says Thank You to mariusmarius For This Useful Post:

    Seedtick (Jan 5, 2018)

  3. #2

    Join Date
    Apr 2017
    Posts
    5
    Thanks
    0
    Thanked 7 Times in 2 Posts

    Dirtinla's Tools


    also harbor freight puts these vises on sale every once in a while

    Harbor Freight Tools Coupon Database - Free coupons, 25 percent off coupons, toolbox coupons - 5" RUGGED CAST IRON DRILL PRESS MILLING VISE

    also for VERY small milling

    https://www.ebay.com/itm/Multifuncti...19.m1438.l2649

    If you have a lathe?





    Let us know how it goes

    -=Fred=-

    2000 Tool Plans

  4. #3
    Supporting Member ncollar's Avatar
    Join Date
    Oct 2012
    Posts
    354
    Thanks
    23
    Thanked 180 Times in 126 Posts
    Marius
    The idea of using a drill press as a mill has been around since the beginning of time. The spindle and the bearings are set up to cut in one direction that is down. Any side ways movement will do nothing but wear a bearing that is not designed for that. Not just that but the chuck will more than likely shack itself off. If you go forward with the idea make sure you have a good supply of cutters because the sizes you will be able to use are rather fragile.

  5. The Following User Says Thank You to ncollar For This Useful Post:

    mariusmarius (Jan 7, 2018)

  6. #4
    Supporting Member astroracer's Avatar
    Join Date
    May 2012
    Location
    Byron, Michigan
    Posts
    310
    Thanks
    20
    Thanked 558 Times in 173 Posts

    astroracer's Tools
    Agree with above. A cheap, desktop drill press uses the downward force while drilling to retain the collet/chuck in the quill. This "upward force" goes away when you try to side mill with an endmill cutter. Any chatter (and there will be chatter) will walk the standard taper drill chuck right out of the quill... A true mill uses a drawbar to hold the collet in the quill. It will not fall out at the first hint of chatter.
    And, as ncollar also alluded too, the bearings in the drill press quill are not designed to operate under a sideways force.
    Just so you know.
    Mark

  7. The Following User Says Thank You to astroracer For This Useful Post:

    mariusmarius (Jan 7, 2018)

  8. #5
    Supporting Member hemmjo's Avatar
    Join Date
    Feb 2017
    Posts
    2,542
    Thanks
    224
    Thanked 1,446 Times in 820 Posts

    hemmjo's Tools
    As with any machine tool the drillpress/milling machine will work ... if you keep its limitations in mind. All of the issues mentioned above; inadequate bearings, danger of the chuck coming loose, minimal cutter selection, etc., are very valid. With those things in mind I have used my old craftsman drill press to "mill" aluminum, wood and plastic for various projects.

    The adapter I made for my lathe, similar to the one Fred showed in post #2 is much better, but the drill press was better than nothing before I had the lathe.

    You got to use what you have access to.

    I would love to have a nice mill, but I have to keep weighing the +'s and -'s of the mill vs the wife. So far, the wife is winning


    Good Luck,

    John

  9. The Following 2 Users Say Thank You to hemmjo For This Useful Post:

    mariusmarius (Jan 7, 2018), PJs (Mar 7, 2018)

  10. #6

    Join Date
    Feb 2014
    Posts
    17
    Thanks
    4
    Thanked 21 Times in 7 Posts

    master53yoda's Tools
    I did a write up on a drill press conversion that address all the negative feedback that is brought up about converting a few years ago. that thread is here
    Homemade Drill Press Conversion - HomemadeTools.net

  11. The Following 2 Users Say Thank You to master53yoda For This Useful Post:

    PJs (Mar 7, 2018), Toolmaker51 (Jan 6, 2018)

  12. #7
    Supporting Member ncollar's Avatar
    Join Date
    Oct 2012
    Posts
    354
    Thanks
    23
    Thanked 180 Times in 126 Posts
    Yoda
    I did not say it was impossible but as I said have a good supply of cutters because of rigidity they will break very easily and the larger ones will take the chuck off the spindle.
    Nelson

  13. The Following User Says Thank You to ncollar For This Useful Post:

    mariusmarius (Jan 7, 2018)

  14. #8

    Join Date
    Feb 2014
    Posts
    17
    Thanks
    4
    Thanked 21 Times in 7 Posts

    master53yoda's Tools
    ncollar if you will look at the thread i posted you will see that i addressed ALL the limitations, i have used a 3/4 endmill on steel with no problems, I also use a a 2 1/2 face mill on aluminium all the time.
    Art b

  15. The Following User Says Thank You to master53yoda For This Useful Post:

    mariusmarius (Jan 7, 2018)

  16. #9
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    And for what we call "my 2 cents"; Drilling and milling are entirely different operations. Even heavy units struggle with side load. Not only are the bearings wrong orientation of contact, the upper and lower are too close together for stability of any kind. Second but just as severe, the round post everything mounts to. Milling wants rigidity; won't happen when the spindle housing is far up that post.
    Now, you won't find anyone here against X-Y table on a drill press for coordinate drilling. The problem will still be size of a X-Y table compatible with a bench drill.

    The variance in results, before and after my post, is due [in order of significance IMHO]
    1. wide range of presses in use to attempt milling,
    2. the backlash and gib adjustments of coordinate table,
    3. cutter types,
    4. speed [rpm] selections,
    5. ability to manipulate a proper and steady feed rate.
    Last edited by Toolmaker51; Jan 6, 2018 at 03:04 PM. Reason: details
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  17. The Following User Says Thank You to Toolmaker51 For This Useful Post:

    mariusmarius (Jan 7, 2018)

  18. #10
    Supporting Member garage nut's Avatar
    Join Date
    Jul 2017
    Location
    Port Elizabet, SA
    Posts
    246
    Thanks
    92
    Thanked 433 Times in 109 Posts

    garage nut's Tools
    I tried it and gave up. It was just going to be for small slots in Ali. As mentioned I build "7" style racing cars, but even that turned out unsatisfactory even after drilling numerous holes in a line and just milling the small bits out. Also as mentioned the chuck falling out and breaking the little cutters

    Watch E Bay it is a lot less frustrating.

    Just my experience...

  19. The Following 2 Users Say Thank You to garage nut For This Useful Post:

    mariusmarius (Jan 7, 2018), Toolmaker51 (Jan 6, 2018)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •