Remove advertisements
Results 1 to 7 of 7
  1. #1
    mklotz mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    1,054
    Thanks
    58
    Thanked 1,780 Times in 675 Posts

    Foredom handpiece hanger

    In a previous post...

    Foredom tool bench hanger

    I described the support stand I made for my Foredom out of a gas pipe bar clamp. A recent close call convinced me that it needs a safe, secure place to hang the handpiece when not in use.

    I gedanken-engineered a whole bunch of complex attachments I could build to attach to the gas pipe and serve as a means of mounting a handpiece hanger. Then I remembered that, when I found the grounding clamps that I used to make a lathe dog...

    One liners

    I was smart enough, seeing their potential utility, to buy two. Remarkably, I knew exactly where the second one was stored and it proved to fit perfectly on the (nominal) one inch gas pipe.

    I turned down a piece of 3/8" allthread to fit the hole in the clamp where the ground wire would go. A piece of the brown stuff (ugh) in the form of 3/4" plywood was drilled to fit the allthread and then Forstner bits were used to create a stepped hole to accept the Foredom handpiece. A slot was made to allow the flexible shaft to pass when hanging the handpiece.




    When everything is in place, the resulting hanger looks like this...


    Attached Thumbnails Attached Thumbnails Foredom handpiece hanger-hanger-1.jpg   Foredom handpiece hanger-hanger-2.jpg  
    Last edited by mklotz; 10-16-2017 at 02:26 PM.
    ---
    Regards, Marv


    Home Shop Freeware
    http://www.myvirtualnetwork.com/mklotz

  2. The Following 2 Users Say Thank You to mklotz For This Useful Post:

    Paul Jones (10-18-2017), Seedtick (10-16-2017)

  3. #2
    ncollar's Avatar
    Join Date
    Oct 2012
    Posts
    95
    Thanks
    7
    Thanked 30 Times in 23 Posts
    Marv
    Very nice fix, looks professional.

  4. #3

    Join Date
    May 2017
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Thank you for sharing your intuitive ideas. I would like a picture that shows what you've done in total. The picture looks like the pipe hanger hangs from a,,,,pipe and it appears the base unit and RPM adjuster are also hanging from the same. It all makes sense but I would like to see your solution, Cheers, Bill Hanson

  5. #4
    Al8236's Avatar
    Join Date
    Dec 2014
    Location
    Kendall Washington
    Posts
    59
    Thanks
    28
    Thanked 56 Times in 22 Posts
    Quote Originally Posted by mklotz View Post
    In a previous post...

    A piece of the brown stuff (ugh) in the form of 3/4" plywood was drilled to fit the allthread and then Forstner bits were used to create a stepped hole to accept the Foredom handpiece. A slot was made to allow the flexible shaft to pass when hanging the handpiece.
    Not dead cellulose carcass I thought that stuff was only for prototyping!
    From the time you're born till' you ride in a hearse, there's nothing so bad it couldn't be worse!

  6. #5
    Content Editor DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,059
    Thanks
    250
    Thanked 456 Times in 413 Posts


    Thanks mklotz! We've added your Foredom Handpiece Hanger to our Storage and Organization category,
    as well as to your builder page: mklotz's Homemade Tools. Your receipt:




  7. #6
    mklotz mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    1,054
    Thanks
    58
    Thanked 1,780 Times in 675 Posts
    Quote Originally Posted by Bill Hanson View Post
    Thank you for sharing your intuitive ideas. I would like a picture that shows what you've done in total. The picture looks like the pipe hanger hangs from a,,,,pipe and it appears the base unit and RPM adjuster are also hanging from the same. It all makes sense but I would like to see your solution, Cheers, Bill Hanson
    Did you take a look at the article referenced in the second line of my post? It describes the hanger construction in detail.
    ---
    Regards, Marv


    Home Shop Freeware
    http://www.myvirtualnetwork.com/mklotz

  8. #7
    mklotz mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    1,054
    Thanks
    58
    Thanked 1,780 Times in 675 Posts
    Quote Originally Posted by Al8236 View Post
    Not dead cellulose carcass I thought that stuff was only for prototyping!
    I have huge respect for the folks who can make beautiful, useful, artistic things from wood. While I admire their talents immensely, I have no wish to try to develop skills to match theirs with the medium.

    To me it's grainy, soft stuff that cracks and splinters and fills the air with dust. Metals are far more pleasant to work and look, to my eye, sensual and elegant.

    That said, I don't hesitate to use wood where its size, resilience and cost suggest it. For me, this is almost always construction rather than artistic applications.

    Nevertheless, when younger I did dabble with attempts at carving the evil stuff...

    Foredom handpiece hanger-marshbird.jpg


    Post your reply!
    Join 20,941 of us and get our 50 Must Read Homemade Tools eBook free.



    50 Must Read Homemade Tools
    ---
    Regards, Marv


    Home Shop Freeware
    http://www.myvirtualnetwork.com/mklotz

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •