Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 6 of 6

Thread: Metal lathe cross slide lock

  1. #1
    Supporting Member xynudu's Avatar
    Join Date
    Dec 2015
    Posts
    47
    Thanks
    0
    Thanked 243 Times in 40 Posts

    xynudu's Tools

    Metal lathe cross slide lock

    This is probably my favourite and most useful lathe modification.

    Simple, non intrusive, easy to use, and necessary for grinding and milling on the lathe.

    It can also be used to overcome and damp out float issues from wear/slop in the cross slide nut.



    Cheers Rob

    186 More Best Homemade Tools eBook

  2. The Following 11 Users Say Thank You to xynudu For This Useful Post:

    Captainleeward (Nov 18, 2017), emu roo (Nov 9, 2023), Jon (Jan 20, 2016), kbalch (Jan 20, 2016), olderdan (Jun 27, 2017), oldpastit (Jul 26, 2019), Paul Jones (Jan 21, 2016), PJs (Jan 22, 2016), Sleykin (Jul 25, 2019), Tonyg (Jul 26, 2019), Tule (Jul 26, 2019)

  3. #2
    Supporting Member Paul Jones's Avatar
    Join Date
    May 2014
    Location
    Del Mar, California
    Posts
    1,231
    Thanks
    5,810
    Thanked 1,440 Times in 655 Posts

    Paul Jones's Tools
    Rob,

    Great suggestion using a ball bearing in the threaded hole. I have a taper gib on my cross slide with a locking screw similar to yours (see Homemade Lever Action Clamping Screws) but I will have to move the locking screw to the other side of the cross slide without a gib when I install a DRO sensor on the gib side. I think using the ball bearing plus a short cylindrical piece of tapered brass may become the locking mechanism on the cross slide side without the gib. Thanks for the idea.

    Paul

    2000 Tool Plans

  4. The Following User Says Thank You to Paul Jones For This Useful Post:

    Sleykin (Jul 25, 2019)

  5. #3
    Supporting Member xynudu's Avatar
    Join Date
    Dec 2015
    Posts
    47
    Thanks
    0
    Thanked 243 Times in 40 Posts

    xynudu's Tools
    Hi Paul.

    Should work great so long as the end of the bolt and brass plug are concave and beveled on the edges to counter spread.

    It annoys me that lathe manufacturers are so mean as to not include one of the these - would cost almost nothing.

    I see the newish Seig C8 has the same setup as in the mod.

    Cheers Rob

  6. The Following 2 Users Say Thank You to xynudu For This Useful Post:

    Paul Jones (Jan 21, 2016), PJs (Jan 22, 2016)

  7. #4
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts
    Thanks xynudu! We've added your Cross Slide Lock to our Lathes category, as well as to your builder page: xynudu's Homemade Tools. Your receipt:

    Last edited by Jon; Oct 27, 2021 at 10:42 PM.

  8. #5
    PJs
    PJs is offline
    Supporting Member PJs's Avatar
    Join Date
    Sep 2014
    Location
    Northern CA
    Posts
    1,841
    Thanks
    8,333
    Thanked 1,118 Times in 718 Posts

    PJs's Tools
    Thanks Rob. Simple & elegant solution...and the ball bearing is icing on the cake! Also like the carriage lock...did you make that too? Not sure I have enough room on my peanut but again a simple, Elegant solution. ~PJ
    ‘‘Always do right. This will gratify some people and astonish the rest.’’
    Mark Twain

  9. #6
    Supporting Member xynudu's Avatar
    Join Date
    Dec 2015
    Posts
    47
    Thanks
    0
    Thanked 243 Times in 40 Posts

    xynudu's Tools
    The carriage lock came with the lathe.

    It's a metal block that pulls up against the underside of the ways - most recent Asian lathes have one fitted.

    I added a hex bolt head, as the original Allen bolt head used to fill up with cuttings.

    I also fitted a heavier bolt as the original was a bit wimpy and snapped early on in it's life.

    Cheers Rob



    186 More Best Homemade Tools eBook

  10. The Following 3 Users Say Thank You to xynudu For This Useful Post:

    Captainleeward (Nov 18, 2017), PJs (Jan 23, 2016), Tonyg (Jul 26, 2019)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •