Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 8 of 8

Thread: Shop fabbed Ball Joint Fixture for Lower Control Arm Fabrication

  1. #1
    Supporting Member astroracer's Avatar
    Join Date
    May 2012
    Location
    Byron, Michigan
    Posts
    310
    Thanks
    20
    Thanked 558 Times in 173 Posts

    astroracer's Tools

    Shop fabbed Ball Joint Fixture for Lower Control Arm Fabrication

    Building the Lower Control Arms for my van project required a book matched set of fixtures to hold the lower ball stud mounting plates in position.
    I designed these in 3D CAD and built them in the shop. Setting ball joint angles precisely was the important part.

    This is a compound tip. 4 1/2 deg down and 3 degs in. Modeling the pieces in 3D let me measure everything very accurately. A few cuts in the bandsaw and a little time on the belt sander and everything was good.

    This is the piece I am locating. It bolts into the fixture which is then screwed down to my jig table.



    See next post.

    186 More Best Homemade Tools eBook

  2. The Following 3 Users Say Thank You to astroracer For This Useful Post:

    kbalch (Jan 27, 2016), PJs (Jan 27, 2016), Toolmaker51 (Apr 16, 2018)

  3. #2
    Supporting Member astroracer's Avatar
    Join Date
    May 2012
    Location
    Byron, Michigan
    Posts
    310
    Thanks
    20
    Thanked 558 Times in 173 Posts

    astroracer's Tools
    This is the end product. Two lower control arms for my BadAst Project.



    Shock mount welded in and some paint thrown on.

    Mark

    2000 Tool Plans

  4. The Following 6 Users Say Thank You to astroracer For This Useful Post:

    extropic (Nov 19, 2017), hansgoudzwaard (Aug 29, 2018), Jon (Jan 27, 2016), kbalch (Jan 27, 2016), PJs (Jan 27, 2016), Toolmaker51 (Apr 16, 2018)

  5. #3
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,057
    Thanks
    771
    Thanked 1,850 Times in 1,652 Posts
    Thanks astroracer! We've added your Ball Joint Fixture to our Suspension category, as well as to your builder page: astroracer's Homemade Tools. Your receipt:


  6. The Following User Says Thank You to DIYer For This Useful Post:

    Quinton 357 (Jun 30, 2020)

  7. #4

    Join Date
    Jul 2017
    Posts
    4
    Thanks
    25
    Thanked 0 Times in 0 Posts
    How did you determine the angle needed?

  8. #5
    Supporting Member astroracer's Avatar
    Join Date
    May 2012
    Location
    Byron, Michigan
    Posts
    310
    Thanks
    20
    Thanked 558 Times in 173 Posts

    astroracer's Tools
    Quote Originally Posted by jackman View Post
    How did you determine the angle needed?
    The angles were determined with a suspension design program. Kingpin, caster and camber were all designed into the angles and setting them up in the fixture was key. There is plenty of adjustment of course but getting the angles right the first time will make for a suspension that is easily set up and easily aligned.
    Mark

  9. #6
    Supporting Member Saltfever's Avatar
    Join Date
    Apr 2012
    Location
    NorCal
    Posts
    343
    Thanks
    389
    Thanked 123 Times in 84 Posts

    Saltfever's Tools
    Quote Originally Posted by astroracer View Post
    The angles were determined with a suspension design program. . . .
    Mark
    The name of that program would be really helpful. Nice idea for the fixture . . . thanks for sharing.

  10. #7
    Supporting Member astroracer's Avatar
    Join Date
    May 2012
    Location
    Byron, Michigan
    Posts
    310
    Thanks
    20
    Thanked 558 Times in 173 Posts

    astroracer's Tools
    https://www.susprog.com/
    Here you go. This is about the best one out there as far as I know. Check it out.
    Mark

  11. The Following User Says Thank You to astroracer For This Useful Post:

    hansgoudzwaard (Nov 13, 2018)

  12. #8
    Supporting Member Saltfever's Avatar
    Join Date
    Apr 2012
    Location
    NorCal
    Posts
    343
    Thanks
    389
    Thanked 123 Times in 84 Posts

    Saltfever's Tools
    Thanks, Mark . . . very much appreciated. Sorry for my slow response. The program looks interesting and agree that is is one of the better ones. I am still checking it out but it looks like more than adequate for what I need.



    186 More Best Homemade Tools eBook
    Last edited by Saltfever; May 3, 2018 at 01:59 AM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •