Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 19

Thread: Source for Spill Proof Oil Can

  1. #1
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools

    Source for Spill Proof Oil Can

    Found this can of oil in the Dollar store. I guess it is a food warmer wick type heater. It is a very easy oil can make over. Just poke a screw driver into the top with the wick. Bend it a bit and it pops out. Drill a hole in the can lid and fit it up with a piece of 3/4 copper tubing and an an extra "collar" made from the same copper tube.
    Solder it up and presto, a "spill proof" oil can. One for the lathe, one for the mill and one for the bench. Easy to clean out the chips with that removable top.

    If you want it to stay put on the mill table just put in a nice neo magnet (3/4" by 1/4") and you will really have to work hard to knock it off the mill.

    Cheers, JR
    Attached Thumbnails Attached Thumbnails Source for Spill Proof Oil Can-dscf0007.jpg  

    186 More Best Homemade Tools eBook

  2. The Following 13 Users Say Thank You to jjr2001 For This Useful Post:

    blkadder (Dec 30, 2017), bvd1940 (Oct 27, 2016), DIYer (Oct 27, 2016), extropic (Dec 30, 2017), gunsgt1863 (Jan 4, 2018), high-side (Oct 9, 2020), Jon (Oct 27, 2016), mwmkravchenko (Feb 12, 2022), Paul Jones (Oct 26, 2016), PJs (Oct 26, 2016), rlm98253 (Jan 9, 2019), Toolmaker51 (May 25, 2018), Tule (Jan 10, 2019)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks jjr2001! We've added your Spill Proof Oil Can to our Machining category,
    as well as to your builder page: jjr2001's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. The Following 2 Users Say Thank You to DIYer For This Useful Post:

    Eaglewood (Mar 12, 2023), txtwang (Nov 29, 2016)

  5. #3

    Join Date
    Oct 2016
    Location
    Seagoville, TX
    Posts
    5
    Thanks
    4
    Thanked 1 Time in 1 Post
    I've made a couple of these..easy to make and they work great!

    Jerry

  6. The Following User Says Thank You to txtwang For This Useful Post:

    jjr2001 (Dec 31, 2017)

  7. #4
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools
    Thanks for your input Jerry, I use mine every time I am using the lathe or mill.
    I have one on each machine to save walking around the shop looking for where I left it last.

    Cheers, JR

  8. #5
    Supporting Member Ralphxyz's Avatar
    Join Date
    Dec 2016
    Posts
    1,564
    Thanks
    2,378
    Thanked 279 Times in 228 Posts

    Ralphxyz's Tools
    So are you using a acid brush or how do you get the oil out?

  9. The Following 2 Users Say Thank You to Ralphxyz For This Useful Post:

    jjr2001 (May 13, 2018), volodar (Oct 1, 2018)

  10. #6
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools
    Acid brushes work great. Small china bristle brushes work fine, and even cheap hobby paint brushes.
    As long as it fits in the spout it will work. Small brush for small jobs, big brush for large jobs.

    Cheers, JR

  11. The Following User Says Thank You to jjr2001 For This Useful Post:

    Paul Jones (May 21, 2018)

  12. #7
    Supporting Member Ralphxyz's Avatar
    Join Date
    Dec 2016
    Posts
    1,564
    Thanks
    2,378
    Thanked 279 Times in 228 Posts

    Ralphxyz's Tools
    Thanks, I want one or two or maybe three!

    Ralph

  13. #8
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,434
    Thanks
    357
    Thanked 6,380 Times in 2,117 Posts

    mklotz's Tools
    As an aside to this topic...

    If you want to go really OCD on this style of no-spill container, the associated mathematics can become moderately complex. Assuming that you want the can to be no-spill on its side and completely inverted there are mathematical relations among the following variables that must be satisfied...

    inner diameter of can
    inner diameter of tube
    projection of tube into can interior

    I actually wrote a computer program to do the calculations but never published it because I realized that nobody is that OCD about such a mundane item.

    At the other end of the spectrum, we have this design that demonstrates that even I am not that OCD...


    Full description here... http://www.homemadetools.net/forum/q...ontainer-38026

    [Although writing a program for a no-spill with conical top would be a fun few minutes of work.]
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  14. The Following User Says Thank You to mklotz For This Useful Post:

    Toolmaker51 (May 25, 2018)

  15. #9
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    Quote Originally Posted by mklotz View Post
    As an aside to this topic...

    If you want to go really OCD.....that nobody is that OCD....even I am not that OCD...
    From my observations and strictly non-professional abilities as a psychologist, in most cases OCD exists within those who don't know why, when or how to apply the energy.
    Marv and other talented persons are happy to wring out performance and desired results at will. Such pursuits are progress, as in why the Middle Ages passed long ago.
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  16. The Following User Says Thank You to Toolmaker51 For This Useful Post:

    mwmkravchenko (Feb 12, 2022)

  17. #10
    Supporting Member Frank S's Avatar
    Join Date
    Aug 2015
    Location
    Peacock TX
    Posts
    11,179
    Thanks
    1,974
    Thanked 8,766 Times in 4,195 Posts

    Frank S's Tools
    Oh wait I missed the middle ages oh well I'm probably thinking middle age I missed that one as well and probably the same time period as well.It seams that I went from perpetual teenager to old man in 1 day this condition also appears to be the same thing it just takes me longer to do less but in my mind it seams like I get more done.
    Never try to tell me it can't be done
    When I have to paint I use KBS products

  18. The Following 3 Users Say Thank You to Frank S For This Useful Post:

    mwmkravchenko (Feb 12, 2022), Paul Jones (May 21, 2018), Toolmaker51 (May 25, 2018)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •