Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 7 of 7

Thread: Ultra-tiny sanding disk

  1. #1
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,434
    Thanks
    357
    Thanked 6,380 Times in 2,117 Posts

    mklotz's Tools

    Ultra-tiny sanding disk

    In the old days Dremel sanding disks attached to a shaft using a central screw. The head of this screw prevented use of the central part of the disk. Later they switched to the EZ-lock system (shown on left in the photo) which attaches from the back and makes the whole disk available for use.

    The 1.25" diameter of the EZ-lock disks was a bit too large for me and so I made a 1" diameter disk (shown in the middle). When I bought Dremel's new 2050 model even the 1" disk seemed oversized so I made a 0.75" disk (shown on right).

    Today I ran into a sanding task that required something even smaller. Rather than turn a new disk, I took the easy way out. I found a nail with a diameter close enough to 0.125" to be grasped in the Dremel collet. Stuck some self-stick sand paper to the head and trimmed away the excess and now I've got a 0.3" sanding disk. Obviously only for very fine work but it worked well in my application.


    A few words about the Dremel 2050 (no, I don't work for them)...

    It's difficult, if not impossible to comfortably hold most Dremels the way you would hold a pencil. It's exactly this hold that provides the best fine motor control for work like lettering. Even my Foredom doesn't do what I want because of the drag of the flexible shaft that drives it.

    Dremel has long sold a pencil-like tool, the Micro, but it's bulkier because of the onboard batteries and then there's the battery life concern.

    What one wants is a tool mains-powered via an offboard voltage converter housed in the mains plug and connected to the tool via a thin, highly flexible cord. And that's exactly what the 2050 is.

    It's low-powered; you won't want to grind your welds or cut 1/4" steel with a grinding disk with it. But it's a real pleasure to use for fine work.

    https://www.amazon.com/Dremel-2050-1...gateway&sr=8-1

    186 More Best Homemade Tools eBook
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  2. The Following 13 Users Say Thank You to mklotz For This Useful Post:

    12L14 (Jul 31, 2019), baja (Jun 28, 2019), davesrepair (Jan 16, 2024), hansgoudzwaard (Jun 30, 2019), Jon (Jun 26, 2019), Okapi (Jun 28, 2019), old_toolmaker (Aug 12, 2021), Paul Jones (Jun 27, 2019), ranald (Jun 27, 2019), Seedtick (Jun 27, 2019), Toolmaker51 (Jun 26, 2019), Tuomas (Jun 28, 2019), will52100 (Jun 27, 2019)

  3. #2
    Supporting Member ranald's Avatar
    Join Date
    Jan 2018
    Location
    Black Mountain Queensland
    Posts
    1,326
    Thanks
    988
    Thanked 361 Times in 253 Posts

    ranald's Tools
    Really like the way you nail those minatures.
    How much tolerance between nail dia and collet?

    Cheers & thanks for posting Marv.

    2000 Tool Plans

  4. The Following User Says Thank You to ranald For This Useful Post:

    Paul Jones (Jun 27, 2019)

  5. #3
    Supporting Member Paul Jones's Avatar
    Join Date
    May 2014
    Location
    Del Mar, California
    Posts
    1,231
    Thanks
    5,810
    Thanked 1,440 Times in 655 Posts

    Paul Jones's Tools
    Marv,

    Very Nice. You have a great substitute for producing an even smaller Dremel sanding disk. Nonetheless, I do like the newer EZ-lock system from Dremel tools for most general cut-off and sanding purposes. What are you working on requiring a much smaller disk?

    Regards,

    Paul Jones

  6. #4
    Supporting Member Okapi's Avatar
    Join Date
    Mar 2013
    Location
    Switzerland
    Posts
    222
    Thanks
    346
    Thanked 132 Times in 76 Posts

    Okapi's Tools
    Good idea, and if I can give you something from my own experience, the best abrasive discs I've found are those used by dentists to adjust the false teeth(about 20mm. In diameter), they are not made for Dremel but you can easily make a part like in the post to hold them, and the best is that they are not expensive…

  7. #5
    Supporting Member Tuomas's Avatar
    Join Date
    Jun 2016
    Location
    Jyväskylä Finland
    Posts
    832
    Thanks
    558
    Thanked 1,834 Times in 507 Posts

    Tuomas's Tools
    I think Dremel should make 45 degree attachment, so you could use it more pencil like way.
    Micro was a little disappointment for me. It would be more usefull without that "safety turn off if wheel jumps or stucks" feature.
    Cutting is annoying when you must turn it back on again and again... Otherwise i like to use it. For my hand it fits nicely.

    Some brands make "roll lock" papers, i know 3M and Suhner. Dremel should use that way too.

    Name:  p-52848-3m-roloc-backing-pad.jpg
Views: 2551
Size:  7.4 KB

    Smallest size that i know for those, is 25mm dia.
    I could try to make smaller shaft for dremel,
    To see would those work. ( Has dremel enough power?)

  8. #6
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks mklotz! We've added your Tiny Sanding Disc to our Disc Sanders category,
    as well as to your builder page: mklotz's Homemade Tools. Your receipt:




  9. #7
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 442 Times in 180 Posts

    old_toolmaker's Tools

    Dental hand piece!

    Marv,
    Have you considered using a high speed air turbine hand piece? They are small in size and easy to hold. I used to have a dental hand piece that would accept dental drills. I could work with this all day without fatigue and noise levels were low.



    186 More Best Homemade Tools eBook
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •