Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 10 of 10

Thread: Using Rosin To Start a Philips Head Screw

  1. #1
    Supporting Member rgsparber's Avatar
    Join Date
    Nov 2012
    Location
    Phoenix, AZ
    Posts
    1,278
    Thanks
    733
    Thanked 2,763 Times in 650 Posts

    rgsparber's Tools

    Using Rosin To Start a Philips Head Screw

    Trying to lower a brass Philips head screw down a deep hole in hopes of engaging the thread at the bottom can be frustrating. A light coating of rosin solves the problem.

    If you are interested, please see

    https://rick.sparber.org/RosinScrewStarter.pdf


    Your comments are welcome. All of us are smarter than any one of us.



    Thanks,

    Rick

    186 More Best Homemade Tools eBook
    Rick

  2. The Following 5 Users Say Thank You to rgsparber For This Useful Post:

    Jon (Dec 4, 2018), oldcaptainrusty (Dec 4, 2018), PJs (Dec 5, 2018), Seedtick (Dec 4, 2018), Toolmaker51 (Dec 4, 2018)

  3. #2
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,434
    Thanks
    357
    Thanked 6,380 Times in 2,117 Posts

    mklotz's Tools
    I use duct seal in the pellet traps I use while practicing my marksmanship. It works well too for temporarily bonding screws to screwdrivers. (Does a pretty good job of sealing ducts too.)

    Back in the day I used the kids' modeling clay. My daughters are adults now and the grandchildren have smart phones so a toy as mundane as clay isn't around any more.

    2000 Tool Plans
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  4. The Following 2 Users Say Thank You to mklotz For This Useful Post:

    PJs (Dec 5, 2018), Toolmaker51 (Dec 4, 2018)

  5. #3
    Jon
    Jon is online now Jon has agreed the Seller's Terms of Service
    Administrator
    Supporting Member
    Jon's Avatar
    Join Date
    Jan 2012
    Location
    Colorado, USA
    Posts
    25,451
    Thanks
    7,928
    Thanked 38,621 Times in 11,284 Posts
    Interesting. Reminds me of the trick to moisten a driver head and dip it into powdered cleaner (like Ajax or Comet) prior to attempting to remove a stripped screw.

  6. The Following User Says Thank You to Jon For This Useful Post:

    Toolmaker51 (Dec 4, 2018)

  7. #4
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,434
    Thanks
    357
    Thanked 6,380 Times in 2,117 Posts

    mklotz's Tools
    Of course, most of the Chinese "brass" screws sold in the big box stores will stick to a magnet.
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  8. The Following User Says Thank You to mklotz For This Useful Post:

    Toolmaker51 (Dec 4, 2018)

  9. #5
    Supporting Member rgsparber's Avatar
    Join Date
    Nov 2012
    Location
    Phoenix, AZ
    Posts
    1,278
    Thanks
    733
    Thanked 2,763 Times in 650 Posts

    rgsparber's Tools
    Quote Originally Posted by mklotz View Post
    I use duct seal in the pellet traps I use while practicing my marksmanship. It works well too for temporarily bonding screws to screwdrivers. (Does a pretty good job of sealing ducts too.)

    Back in the day I used the kids' modeling clay. My daughters are adults now and the grandchildren have smart phones so a toy as mundane as clay isn't around any more.
    Marv,

    Duct seal is new to me. Interesting product.

    Thanks,

    Rick
    Rick

  10. #6
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,434
    Thanks
    357
    Thanked 6,380 Times in 2,117 Posts

    mklotz's Tools
    Quote Originally Posted by rgsparber View Post
    Marv,

    Duct seal is new to me. Interesting product.

    Thanks,

    Rick
    It's perfect for a backstop. Even a high power 0.22 pellet can't penetrate and, since the pellet is trapped, there are no ricochets. Plus, with patience the spent pellets can be harvested and used for weighting various things around the shop like round-bottomed soda cans turned into small parts trays.

    I've never actually used it for its intended purpose. However, when the installer drilled through the house wall to install the Verizon cable I watched him seal the hole with the stuff.
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  11. #7
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    Yes Marv's duct seal makes good ballistic putty. An inch seems to stop any pellet, even my 5mm's. Sealing wire entry is a common use. Real important marine use inside their stuffing tubes for watertight integrity.
    Cleansers add 'bite' to screwdriver bits. A bit of torn off aluminum foil can help with Phillips or straight screw slots. Both leave particles, not always electrically or mechanically copacetic.
    Rosin, warmed with a butane lighter makes a nicely brittle glue that really holds fasteners.
    Finding modeling clay is worthwhile; holds thread wires, replicate fillets and radii, [can slice for comparators], reveal clearance when fitting parts, apply underside of thin sections to dampen vibrations while subtractive machining, adheres on most surfaces - weighs easily for static balancing, shelved object pressed into 3 small cone 'feet' might avert loss during earthquakes. Don't have a tube mic? With a little clay and small bearing ball, now you do.
    I keep a lump in prescription container for the thread wire trick. In reality it's plumbers putty, a nice plain gray color. Not big fan of pink, neon green or white. Brown has a lot of practical joke applications...
    Last edited by Toolmaker51; Dec 4, 2018 at 05:41 PM. Reason: 1st today...edits make me feel alive!
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  12. The Following User Says Thank You to Toolmaker51 For This Useful Post:

    PJs (Dec 5, 2018)

  13. #8
    Supporting Member JoeVanGeaux's Avatar
    Join Date
    Jun 2018
    Location
    Magnolia, TX
    Posts
    168
    Thanks
    160
    Thanked 57 Times in 44 Posts
    Quote Originally Posted by mklotz View Post
    Of course, most of the Chinese "brass" screws sold in the big box stores will stick to a magnet.
    Wow, isn't that the truth!!

    Nowadays, you have to first borrow a magnet from the hardware section to "proof" their "brass" fittings and things like the mythical "solid brass" door kickplates!

  14. #9
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,434
    Thanks
    357
    Thanked 6,380 Times in 2,117 Posts

    mklotz's Tools
    Quote Originally Posted by JoeVanGeaux View Post
    Wow, isn't that the truth!!

    Nowadays, you have to first borrow a magnet from the hardware section to "proof" their "brass" fittings and things like the mythical "solid brass" door kickplates!
    Part of your shopping pocket tools...

    http://www.homemadetools.net/forum/pocket-tools-40671

    should include a magnet.

    I'm planning to bore a hole in one of the tools shown and glue in a small neodymium magnet for testing for the elusive Chinese ferrous brass.
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  15. #10
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts
    Thanks Rick! We've added your Scew Starter to our Fastening category, as well as to your builder page: Rick's Homemade Tools. Your receipt:




    186 More Best Homemade Tools eBook

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •