Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 5 of 5

Thread: Chuck key for one of my Lathes

  1. #1
    Supporting Member Frank S's Avatar
    Join Date
    Aug 2015
    Location
    Peacock TX
    Posts
    11,178
    Thanks
    1,974
    Thanked 8,766 Times in 4,195 Posts

    Frank S's Tools

    Chuck key for one of my Lathes

    One of my Lablond lathes came with a short chuck key that looked like it had been left in the chuck when the lathe had been turned on.
    I simply hadn't taken the time to make a new one, but yesterday I finally got fed up with it since when using the 4 jaw if I had to widen the jaws out very far the key was a bother to use
    I grabbed a couple pieces of rod then being too lazy to set up the mill I just ground and filed the square key portion in 1 of the pieces then welded them together. Stupidly simple to make these things but a little time consuming non the less.
    Chuck key for one of my Lathes-20170405_130152aa.jpg
    As you can see the old one has seen better days
    Chuck key for one of my Lathes-20170405_130724aa.jpg

    186 More Best Homemade Tools eBook
    Never try to tell me it can't be done
    When I have to paint I use KBS products

  2. The Following 2 Users Say Thank You to Frank S For This Useful Post:

    Paul Jones (Apr 8, 2017), Seedtick (Apr 9, 2017)

  3. #2
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,433
    Thanks
    357
    Thanked 6,378 Times in 2,116 Posts

    mklotz's Tools
    When centering work in the 4jaw it's often handy to have a wrench in each of the two horizontal jaws. Often there's less clearance to operate the rear jaw and so a shortened wrench makes things easier. In fact, I've purposely made short wrenches for several of my 4jaws for just that reason. Perhaps that's how your short wrench originated.

    Shifting chuck jaws long distances can be expedited easily with an electric screwdriver; see here...

    http://www.homemadetools.net/forum/s...uck-jaws-26219

    2000 Tool Plans
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  4. The Following User Says Thank You to mklotz For This Useful Post:

    Paul Jones (Apr 9, 2017)

  5. #3
    Supporting Member Frank S's Avatar
    Join Date
    Aug 2015
    Location
    Peacock TX
    Posts
    11,178
    Thanks
    1,974
    Thanked 8,766 Times in 4,195 Posts

    Frank S's Tools
    Marv I suspect that the short key may have gotten bent just that way by using it in the back side of a 4 jaw then forgetting it was there when the lathe got switched on causing it to hit the back of the head stock housing I've never used the 2 key approach too fiddling to try and reach back there and very limited movement would be possible anyway.
    I don't remember how long it's been since I owned an electric screw driver and doubt if 1 has ever been made that would move the jaws on chucks the size that mine are A drill yes
    Even though my smallest 3 jaw chuck for this lathe is 12" the short key only worked when used in the straight up vertical position or perfectly horizontal as long as the carriage was out of the way and the high low lever was in the high speed position
    On my 1930's era 16 inch Lablond all of this would be possible since it has a small head stock
    Never try to tell me it can't be done
    When I have to paint I use KBS products

  6. #4
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks Frank S! We've added your Chuck Key to our Miscellaneous category,
    as well as to your builder page: Frank S's Homemade Tools. Your receipt:




  7. #5
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    I've also made a couple keys over time. They were remnant chrome-moly tubing handle and body. Body has pressed and pinned square; then a solid plug is barely slip fit for handle. A lot like a T-bar for socket wrenches, can nearly double the torque when drawn to one side. The chuck is 12" and old bent key, heavy and cumbersome in repeat parts.



    186 More Best Homemade Tools eBook
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •