front grill gard haul rack combo

Printable View

Nov 12, 2019, 09:02 PM
Frank S

5 Attachment(s)

front grill gard haul rack combo

I wasn't going to publish this until I had time to finish it but today the opportunity came up to make a trip to the steel supply making the grill gard/ haul rack an official tool in use I'll go ahead and publish.
the grill guard is made of 1 1/4" sch 40 pipe with 2 1/2" vertical supports.
later it will have some bars and more smaller pipes added to finish the guard portion
the haul rack telescopes to above the top of the cab it is made out of 2" pipe and 1 1/2" pipe
the temporarily the front bumper was welded in place
Attachment 32018

Attachment 32019

Attachment 32020

Attachment 32021
a load of purlin to begin the roof of my shop
Attachment 32022
Nov 12, 2019, 10:32 PM
DIYer


Thanks Frank S! We've added your Pickup Hauling Rack to our Automotive category,
as well as to your builder page: Frank S's Homemade Tools. Your receipt:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/homemade-pickup-hauling-rack"> <img src="/uploads/227741/homemade-pickup-hauling-rack.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/homemade-pickup-hauling-rack">Pickup Hauling Rack</a> <span> by <a href="https://www.homemadetools.net/builder/Frank+S">Frank S</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/rack'>rack</a>, <a href='https://www.homemadetools.net/tag/guard'>guard</a>, <a href='https://www.homemadetools.net/tag/pickup'>pickup</a> </div> </div> </div> </div>
Nov 16, 2019, 12:19 PM
metric_taper

This frame extension modification all makes sense now, with your posts on the truck repairs and 'cattle guard' addition. All leading up to making a heavy haul of material.
I've hauled long boards in my light duty 1/2 ton, via a home built ladder rack using the existing side board holes in the truck box. This front support would have been handy when hauling 16' material.
How is the perlin install going? I'm guessing you've made a crane to 'fly' them in place.
Nov 16, 2019, 04:21 PM
Frank S

Quote:

Originally Posted by metric_taper

This frame extension modification all makes sense now, with your posts on the truck repairs and 'cattle guard' addition. All leading up to making a heavy haul of material.
I've hauled long boards in my light duty 1/2 ton, via a home built ladder rack using the existing side board holes in the truck box. This front support would have been handy when hauling 16' material.
How is the perlin install going? I'm guessing you've made a crane to 'fly' them in place.

Right now I have been removing the body from a school buss the body is 36 ft long and I am going to lift it up and place it on top of the container to be either an office or for storage later I will build an elevator for raising heavy items
Thinking about mounting scaffolding on the bus chassis making it just less than the height under the trusses. I can platform the top of the scaffolding and install folding safety rails that way I can roll the bus to where I need it and have a platform wide enough and long enough to install at least 2 of the 30 ft purlins spanning 3 trusses without having to move my scaffold rig it will be handy for installing the insulation and roof materials as well
Nov 16, 2019, 08:31 PM
metric_taper

If your 6x2C channel is .2 inch material, that's pretty heavy for 30ft, 8.2lbs/ft ~246lbs (lightest beam in 6 inch C shape; C6x8.2). But you indicated you hauled less then 1000lbs, and 10 of these are 2.5ton, so I'm missing something. Add in the side wall beams, 4) C4X5.4 @30ft (or were these C4X7.25?).

Elevator should be interesting to see what you come up with.
Nov 16, 2019, 09:54 PM
Frank S

Quote:

Originally Posted by metric_taper

If your 6x2C channel is .2 inch material, that's pretty heavy for 30ft, 8.2lbs/ft ~246lbs (lightest beam in 6 inch C shape; C6x8.2). But you indicated you hauled less then 1000lbs, and 10 of these are 2.5ton, so I'm missing something. Add in the side wall beams, 4) C4X5.4 @30ft (or were these C4X7.25?).

Elevator should be interesting to see what you come up with.

This is C purlin not C channel the 6x2 Purlins weight 2.63 lbf 789 lbs for 10 pieces
the 4 x1 1/2 purlin weight is 1.91 lbf 286.5lb for 5 pieces
the 6 " connector sleeve is roughly same weight per ft so 65.75 lbs for 1 25 ft stick
same goes for the 4 " connector sleeve so 38.2 lbs for 1 20 ft stick
total weight around 1179.45
it takes over 6000 lbs in the bed of the old truck before the springs reach the overload helpers.
But with the load situated so far forward due to the length and my front end can only take a max of 5600 lbs total and empty there is 3,200 on the steer so given that 2/3rds the load was being carried on the front axle around 786 lbs of the load was on the steer bringing the axle load up to just shy of 4000.
I would have preferred they had loaded me about 3 feet further to the rear even if I would have needed to flag it due to having a 6 ft overhang to the rear instead of the less than 3 ft that I had but it was what it was the next time it will be loaded further to the rear as I plan on reducing the 3 remaining trips into 2 or I may just go for 30 more of the 6" purlin and 1 more 6" connector sleeve which will complete the roof requirement
Nov 17, 2019, 03:21 AM
metric_taper

I see steel perlins, but they are in the Z shape. C form never came up with quick search. So 80lbs is not the worse dead lift. But I know at my age that is getting dangerous, in a 30ft length.
I'm 2 years behind you. Worse, I have an allergy to any OTC NSAID, including aspirin. I had been using Ibuprofen for the past 30 years, and now can't use anything.

At least you can keep working through some of the winter, except for the random snow fall in your area. Amarillo shows average of 19 inches. I guess you have to fight that too.
Nov 17, 2019, 08:17 AM
Frank S

Quote:

Originally Posted by metric_taper

I see steel perlins, but they are in the Z shape. C form never came up with quick search. So 80lbs is not the worse dead lift. But I know at my age that is getting dangerous, in a 30ft length.
I'm 2 years behind you. Worse, I have an allergy to any OTC NSAID, including aspirin. I had been using Ibuprofen for the past 30 years, and now can't use anything.

At least you can keep working through some of the winter, except for the random snow fall in your area. Amarillo shows average of 19 inches. I guess you have to fight that too.

Yeah anyone who has never been to West Texas or the Panhandle in the winter during one of the random thankfully not very frequent snow storms don't even believe it ever snows in TX. Also another fortunate thing for us is it may be near zero one day with a North wind blowing across the barbed wire fence at a steady 35 to 45 MPH with a 3 to 6 inch snow fall one day then be nearly 80° then settle in mid 50's for a week or so.
One year quite a number of years back An Aunt and Uncle drove down for a visit from northern Colorado in Mid October At the time I was living Near Dalhart, the afternoon they arrived it was in the low 80s' the next morning there was 18" of snow on the ground with the wind howling and the mercury didn't seem to eve want to stop falling finally leveled off just above zero. My Aunt could do nothing but complain that she was freezing to death the whole time they were visiting saying that back home when it got to near zero they could still wear short sleeved shirts. I just told her to stick around in a few days it would be warm enough to go swimming again.
Some friends dropped by this Oct in their 95 Prevost motor coach from Ct. for a couple weeks while here he helped me install the trusses on the shop also he got to experience first hand the Texas weather mood swings an early light dusting of snow the mercury going from mid 70's one day to 10° the next morning then back into the 60's a couple days later. On their way back through from Las Vegas they dropped the motorhome off for me to do some work on it over the winter
Nov 17, 2019, 08:40 AM
Crusty

I used to carry sticks of steel slung below my truck frame on chains but general driver competence has become so low these days that I'd be afraid of someone else driving into the extended sticks unless I cut a small car body in half and strapped each half to the ends of the sticks.

Now that grill guard looks like something than not even my dad could bend.
Nov 17, 2019, 08:48 AM
Frank S

Quote:

Originally Posted by Crusty

I used to carry sticks of steel slung below my truck frame on chains but general driver competence has become so low these days that I'd be afraid of someone else driving into the extended sticks unless I cut a small car body in half and strapped each half to the ends of the sticks.

Now that grill guard looks like something than not even my dad could bend.

When I get around to adding in the rest of the guard bars it should be a deterrent to the random hog or deer destroying the front end of the old truck, I could encounter at night around here.
Nov 17, 2019, 08:52 AM
metric_taper

Quote:

Originally Posted by Frank S

Yeah anyone who has never been to West Texas or the Panhandle in the winter during one of the random thankfully not very frequent snow storms don't even believe it ever snows in TX.

I've been here in the Iowa "tropics" for 35 years now. I moved here from Grand Forks, North Dakota. When your born there, the winters are no bother, you know how to dress for them. When I left in 84, the February lows were -40F, with highs in the -30s, that lasted most of the month. I'm living about 50 miles south of what I call the perma snow line, where we get melt offs and freezing rain, but not enough long term snow to own a snowmobile. It mostly stays around +20F for highs of the day. But it does shut down my outdoor tasks. And this year it's a month early. Leaves are still on the trees.
So scrap steel is $25/ton, but the steel I bought to fix my skid steer bucket 3 weeks ago, was $60 for a 5 foot strip of 4 inch x 1/2 bevel edge. Seems the price of new steel has not come down, but the tariffs has destroyed the scrap market. Hold on to your scrap!
Nov 17, 2019, 11:38 AM
Frank S

Quote:

Originally Posted by metric_taper

I've been here in the Iowa "tropics" for 35 years now. I moved here from Grand Forks, North Dakota. When your born there, the winters are no bother, you know how to dress for them. When I left in 84, the February lows were -40F, with highs in the -30s, that lasted most of the month. I'm living about 50 miles south of what I call the perma snow line, where we get melt offs and freezing rain, but not enough long term snow to own a snowmobile. It mostly stays around +20F for highs of the day. But it does shut down my outdoor tasks. And this year it's a month early. Leaves are still on the trees.
So scrap steel is $25/ton, but the steel I bought to fix my skid steer bucket 3 weeks ago, was $60 for a 5 foot strip of 4 inch x 1/2 bevel edge. Seems the price of new steel has not come down, but the tariffs has destroyed the scrap market. Hold on to your scrap!

10-4 on save my scrap steel.
I did some work on a pipeline up in Montana one winter. A bunch of us showed up to test out one morning. the temp must have been in the -30 range we had spent the weekend in a Motel in Bute and everyone's machines were cold soaked almost to the point of having slush in the antifreeze at the job site the Foreman told me that I might as well head back to Texas as he was no going to have a Holbart machine on his pipeline let alone a dang diesel as he called it.
I said OK, but I thought that should get the chance to at least bust out on my test, so I lingered while all of the Gasoline Lincoln SA 200 Pipeliner machines were cranked over and not a single one of the things would start. The line boss said well let's see if that heap of your will at least start.
I flipped the switch and didn't push the start button I just poured me a cup of coffee while he was saying just as I thought that thing wont start until summer.
OH it'll start probably before you finish your cigarette, he took another puff and about then my machine cranked over on its own a couple of times then was sitting there idling away. He dropped his coffee and his cigarette and stood there open mouthed and bug eyed.
I un spooled part of my leads and said hook em up boys DR. Holbart is ready to defibrillate your Lincoln's hearts. I worked in a tent the whole time we were on the pipeline making transition manifolds and turn backs and never did test out but every morning a few of the Lincolns needed defibrillating.
I loved the auto start feature on my machine it wouldn't even turn over until the preheaters did their work.
Nov 17, 2019, 12:42 PM
metric_taper

Quote:

Originally Posted by Frank S

Gasoline Lincoln SA 200 Pipeliner machines

My brother worked in Houston as a rig welder. Seems this was the only accepted machine they were allowed to own. He always bad mouthed my Miller Synchrowave. He was a talented welder, started in high school. I call my welding 'sh*t-ass', but I get penetration, just looks like crap. He retired early from welding when he moved to Minnesota. Sold off his SA200, and purchased a Miller plug in model.
His widow just gave me his Miller Maxstar 140. I have not had the chance to use it yet, but reading the blogs on it, it won't burn rod unless powered with 240VAC. It is an older unit, darn these were expensive in the day. It's smaller then a shoe box. Some Austrian inverter company made the electronics, and failed in making it work at 120VAC. My intent is to use it to TIG the sheet metal repairs in my 57 Chevy truck. I've never use lift TIG before, so that should be interesting. I'm used to using the foot pedal, with HF start. So we shall see if I can plug weld panels in place this next spring. That's the truck I purchased some of the KBS products for. The driver side toe kick floor is the first to repair. I just wish I had the room to remove the cab and clean up all the rust properly.
May 2, 2026, 02:04 AM
mansworld

He could have made the rack removable by adding a front mounted receiver hitch. The front hitch could be utilized to receive other devices like a snow plow, a boom crane, a winch, you name it.