Printable View
Grease applicator.
<video controls autoplay loop> <source src="https://diqn32j8nouaz.cloudfront.net/grease_applicator.mp4" type="video/mp4"> Your browser does not support the video tag. </video>
Previously:
https://www.homemadetools.net/forum/...078#post134248
https://www.homemadetools.net/forum/...977#post120095
https://www.homemadetools.net/forum/...156#post130363
I think he has used that gun once or maybe twice.
All the worlds graphite gone onto one machine.
Cheers
Probably not graphite grease but molybdenum disulfide grease, known simply as moly greaseQuote:
Originally Posted by ranald
Thanks Frank. Gee, ad some copper and they can blow their socks off, to boot.Quote:
Originally Posted by Frank S
We've all greased bearings. By gun, thrown hard into a bucket, or fingers of course.
A company [Odetics, Anaheim CA] built ultra high grade reel to reel tape decks for various space programs, US and abroad. Sturdily engineered to withstand G force of rocket launch.
These had several ball bearings, about 1.5 and 4mm bore. These were cleaned of assembly grease 101% and regreased with specialized lube.
Under a microscope.
Clean room of course, in an electronic lab scale.
With a precisely metered air driven syringe and needle.
Each ball [8-10?] got a milli-milli gram right where ball and cage met. 1 pin point dot.
I like the size of the slewing ring bearing and gear teeth better at least I wouldn't need a microscope to see itQuote:
Originally Posted by Toolmaker51
I cant imagine the sterility of that workshop.Quote:
Originally Posted by Toolmaker51
Aside=My 24 y.o. son who works for an auto supply co wanted to borrow my small box trailer yesterday. (They get all kinds of training in his job and he is the only one allowed to do fitments.) OK, I said, but we will snig up the wheel bearings on driver's side before you go. No, he had to go and get new bearings as he didn't want it exploding on the hiway. "Ok", I again said, "go ahead" (he had done the last set when he borrowed it a short while back & doubt if it had done 1000Ks). When he went to remove cones I told him no bother as there was no damage to them (or the bearings) but it HAD to be done every time the bearings were done: "Ok" repeated. After about an hour of mucking around & my advising to use the engineers vice & 20 ton press, I almost had to snatch the hub from him, as his new girl friend and her mom, were watching. 5 mins to the shed and back= done. Assembly was interesting: 3 or 4 pairs of disposable gloves later and looking at utube and the rear seal (different to original) and his complaining of must be Ford not GM bearings BS, he finally listened to me (I kept walking away as it was too stressful watching & advising & no heed being taken= he has to learn after all). His girlfriend's mother is a doctor (gyno I think but profession of no consequence) and had advised that a girl friend of hers bought a house part and installed watching utube & saved heaps of $$$. So, winding him up with support: too many cooks!
Anyway, he finally removed and wrecked the back to front rear seal and replaced it with the previous one & proceeded to fit the hub. You know when you advise the rubber goes to the bearing and the metal side to the outside you think it is CLEAR how to install. (I won't go into the greasing of the tapered roller bearings as too painful). Mom in law to be, gave further advice..........and he tightened the nut and started to replace the split pin. I said to not bend the pin yet. "WHY?"= "It is NOT tightened correctly" was my answer: "I'll show you how we did it in the old days BEFORE UTUBE and our boat trailer never got stuck on the side of a road or hiway from bearings". I first registered that trailer in 1972 and never been caught by it either. ( I was held up with the boat only once from someone had apparently tried to steal a wheel and was interrupted, and the wheel passed us at 100kph). I showed him by fitting the wheel to the hub and demonstrated that his method could be improved by following a process= not rocket science. He actually learned this time, I think: would never listen as a child and knew everything. Might be a chip off the old block: LOL.
Our kids were sent to us to bring up and they inturn TEACH US SOME LIFE LESSONS. I always had the patience of a rock, as my elder brother says, but kids can make some of us frustrated: me included.
Sorry Ranald but I have to say this. You first mistake was allowing him anywhere near your trailer wearing latex disposable gloves. those gloves do have a purpose but just about the only time is when using KBS paint because if that stuff gets on you it will be there until you shed the top 3 layers of your skin usually a couple weeks to wear off completely.
when greasing bearing if I am only doing a couple it is glob of grease in palm, work bearing into the grease by scraping the rim of the cage against you palm the grease will leave your hand super clean in that area for clean up before heading to the hand cleaner or soap and water I like to scrub my hands in automatic transmission fluid it will dissolve the grease and any grime much better than the best grit hand cleaner
That is the way I (my dad showed me) have always done it. Even when contract parks mowing with my sealed tractor mower bearings, I would remove one seal or sometimes both and work in the palm as the first "ubeaut" sealed ones lasted no time without proper grease insertion. Eventually, soon after, I would remove the top bearing seal alltogether, and not replace, so that i could still grease in the usual manner after about 5 hrs continuous work (ie: twice daily): I left/replaced the bottom one as another line of defence (the Kubota hubs have a pretty good bottom seal) against bailing twine, used by council for cheap tree tieing (reusable tree tie was stolen), and fishing line used for kites and fishing.Quote:
Originally Posted by Frank S
I told my son I thought those gloves were not great for the largest body organ and the response was better than grease: I mentioned old mechanics with reply like the grease is different now=point taken: somewhat like "oils aint oils".
I use an orange/citrus product to clean hands of most grease/oil etc. It is excellent and the hands feel fresh as well.
The guy whos truck and trailers I do all of the work on dropped his 2001 Mack off last week for some much needed TLC. and a few other thing he wanted done. I replaced the shocks on the steer axle the shocks under the sleeper the belt tensioner tightened up a few things the will just need tightening after a few 100,000 miles.Quote:
Originally Posted by ranald
I noticed the main supply hose between the power steering pump and the reservoir was leaking at the pump looked like it had been doing this for quite some time. tried tightening the clamp but it was already tight so thought it could be the o ring in the fitting that was doing the leaking. the pump shares the engine oil to a lessor extent, so you know what color that oil gets I removed the hose and the fitting to drain it then replaced the o ring and decided to rotate the fitting slightly to allow me to cut off about 2 inches of the hose to have a fresh clamping surface. My hands had that black engine/ PS oil ground in deep but when I reached for a qt of Mercon and poured it over them then scrubbed like I was getting to go into surgery my wife thought I had lost my mind She said you have a 2 gallon dispenser of that Fast Orange gritty hand cleaner why didn't you use that. I said I will but first I want to get my hands a little cleaner. She just shook her hear and said you and your old Indian tricks and walked of muttering using transmission fluid to clean off oil craziest thing I ever heard of, crazy old man would probably take a bath in the stuff in if he--- but by then she was far enough away that I couldn't hear what she said next.
Ha Ha, very funny that some don't see it. I used to use an excellent product like Fast Orange but it went of the market. It was fairly gritty and needed a special pump that was s/s mostly and quite expensive. Of course, excuse pun, one could pour grom container but was thick so could be wasted & then the container needed cleaning.
Marketing!
Its still sold here and quite popular but no where near as good as a product that was called ZEP it may still be around but haven't seen any in a long while.Quote:
Originally Posted by ranald
A company that I did contract welding and mobile machining for bought it by the barrel then refilled their inverted hand cranked pump go-jo containers, for washing up that were scattered all around their shops.
The guy that owns the truck I'm working one makes sure that I never run out of things like shop towels, hand cleaner hydraulic oil, antifreeze ATF, motor oil, gear oil, tube grease, trailer hub oil, lights DOT air lines, brass fittings, hub seals, and a lot of other things. His line of thinking is that if he or one of his friends pass through in the middle of the night and happens to need something for the truck or trailers I will have it here. Plus it makes their bill a lot cheaper, especially when he drops his rig off if I don't have to run to town for things.
Good News. You can clean up for supper.
https://www.zep.com/
yeah not sure why it is not still green maybe purple has more sex appealQuote:
Originally Posted by Toolmaker51
Thanks guys for info. I think Zep may have been the brand name : round container about 1/2 gallon(2 Litres) large lid & screwed into applicator. Used arm to depress s/s lever & catch glug in other hand. Very citrus like and cut through sump oil & grease like a hot knife in butter. I tried sourcing here even on limited net in those days with no avail. Fast Orange is good enough for me nowadays as I do mostly woodwork. Fast orange doesn't remove enamel etc but small amt left wears off soon which i think is better & cheaper than using thinners or gloves.
Talking about dinner it's breaky time for me.
For one of the fireworks shows we worked on a guy brought a tub of disposable hand wipe towels from the oil refinery he works at. I've seen less aggressive rasps! Might be good for getting oil off, not so much for wiping your face after a day of setting up racks in July.
It was a shop repairing printing equipment; worst silicone based grease and ink possible. We used woven synthetic towels like that, red and a lighter red in a chevron-like pattern. Not an ideal facial scrub. Very coarse; I blame my personality on those.
My joke about them regarded finger print eradication; started quips about witness protection programs.
if its not rough it can't be tough. Knew a guy who worked on delicate micro sized things he used facial tissues to wipe his hands with and complained that some brands were not soft enough for his skin. Personally I don't mind using burlap as facial tissues when you have a honker you need to expel from your nasal cavities burlap will do just fine. I used to use a uniform service to provide me with shop towels that dry-cleaning solution smell in them to me meant they would be absorbent and rough enough to rub the grime off your hands and everything else. I now have to wash my own shop towels most will be caked with grease and grime never just soiled I wouldn't dare put a load of them in the washing machine before plunger washing them in 5 gallon buckets of extremely hot water and the KBS klean solvent several times then hand wringing them and doing it again and again then finish off with dawn dish detergent more rinsing then hang to dry that red dye in those things will never completely stop leaching out until they are a pale pink in colorQuote:
Originally Posted by Toolmaker51