Holding a nut in place inside tubing - GIF

[Altair]

Holding a nut in place inside tubing.




Previously:

Spinning nuts in tight spaces - GIF
Angle grinder nut removal tool - video
Transmission tower lock nuts - GIFs
Nut tapping machine - GIF
Hydraulic nut splitter - GIF

[Toolmaker51]

(almost) Did this today, putting an old Monkey-Wards table saw together. For unknown crazy reason, there are 3 bolt/ washer/ nut sets in each corner, where frame corners, saw cover box, and Unistrut like base meet.
Tried magnet, too thick for allowable space.
Used masking tape instead.

[Beserkleyboy]

Toolmaker, Thanks for the Monkey Wards mention! A real blast from the past. My old man used to call it that...we had a store 1/2 mi away from our family lumber yard in Pleasant Hill, CA...I haven't thought of that in YEARS! Cheers
Jim

[daniel82]

My first 'real' job was warehouseman at Store #1620 in Red Bluff, CA...worked briefly at one in L.A, also. Much more laid back than being a humanbot at some faceless Amazoncwhse.

[daniel82]

Monkey Ward Store #1620 , I mean.

[Floradawg]

(almost) Did this today, putting an old Monkey-Wards table saw together. For unknown crazy reason, there are 3 bolt/ washer/ nut sets in each corner, where frame corners, saw cover box, and Unistrut like base meet.
Tried magnet, too thick for allowable space.
Used masking tape instead.

You're just now getting around to assembling it. You're at least as bad as me.

[Toolmaker51]

You're just now getting around to assembling it. You're at least as bad as me.

I'd say ouch, but not the case.
It was assembled while I test ran it a couple days before. I broke it down, was unmanageable loading into car (and believed it be worse removing). That allowed blowing out saw dust, running motor separately, and general attention to various fasteners. Only thing found out of sorts, the blade of last user is a 6" from a portable circular saw. Lowest height of arbor from table indicates 8-1/2" is correct.
I'm no carpenter; initial use will enclose open area of trusses and plate/ eaves of my roof.

[Floradawg]

I'd say ouch, but not the case.
It was assembled while I test ran it a couple days before. I broke it down, was unmanageable loading into car (and believed it be worse removing). That allowed blowing out saw dust, running motor separately, and general attention to various fasteners. Only thing found out of sorts, the blade of last user is a 6" from a portable circular saw. Lowest height of arbor from table indicates 8-1/2" is correct.
I'm no carpenter; initial use will enclose open area of trusses and plate/ eaves of my roof.

Just funnin' with ya.

[Toolmaker51]

Hats off to our collective 'old man'.

It's pointless trying to forget certain things individuals count as history. Nearly all those giant retail corporations vaporized, or so reduced to appear so. Cashways/ Payless, 84 Lumber, K-Mart, Thompson - Sutherland, J.C. Penney, Sears Roebuck, National Lumber (became Home Depot), Buena Park Lumber (is Ganahl) Eagle Home Improvement (now Lowe's)...lots of industrial suppliers too. Last three years, I've done a lot of driving, none of those are visible.
All had appreciable service, loyal customers, good distribution, identifiable brands, owners, CEO's.
Now, so few replacements equal those, aren't supporting US manufacture very well, and think online support equals that retired tradesman in hardware, electrical or plumbing.
Nope!

[Beserkleyboy]

Well said, mate...The demise of large corporate brands as Sears, JC Penney, K Mart (our's is going gangbusters!) et al, is against every basic tenent of good business practice. The sad irony is that the 'modern' customer has no idea of what constitutes a 'good' business from a customer's perspective. We, my mum and I, recognised the shift early in the piece, forced by our Southern Pacific Railroad landlord after cessation of service on the Contra Costa spur line, to determine whether to relocate the Pearson Lumber Co to a new home. Home Depot was just setting up shop nearby. A tour of Home Base in San Leandro (I think) in 1984 help us understand the future of the industry...She, in '85 was looking forward to retirement. We did the sums and the cost and years of new hard work to re-establish the business in a new location with a whole new customer base, was not something I would have wished on her, as I could not have done it alone (financially). We closed a 40 year old successful business and liquidated, much to the chagrin of longterm employees and gobsmacked customers. I emigrated to Australia 2 years after and found success in the 'timber' business with several ventures. Retired now, with a cabinetmaker hobby business, I support a local family owned timber yard (105 years old) nearly exclusively for all timber needs, but sadly, use Bunnings (think Home Depot) for hardware and fixings. And as for local manufacture, our builders used to whinge about 'cheap Jap steel' in easily bent nails, while happy as Larry to buy PSS (Pacific States Steel) nails because the company was in San Leandro, CA...but they were fully imported from Japan...go figure. I still try to support local/small if at all possible. Thanks for your continued input here. Cheers.
Jim on ANOTHER rainy day in Sth Cst NSW, AUS