Re-think on wire bender for making chain links

10 Attachment(s)

Hi All

After posting the wire bender to make the chain links using a M8 nut and bolt, https://www.homemadetools.net/forum/...g-chains-77629 I wasn't totally happy with the shape of the links and how fiddley they were to produce. So this was playing on my mind :confused:, I had to think of a better way to form the links, and I couldn't find anything on the net on how to form small chain links :mad:. So after a few days contemplating the best way forward I put pen to paper (yes a PEN with real ink) and started to play around with some ideas on how to improve the shape and production of these tiny links.

As I need to make approximately 120 links for the steering chains on my 1" scale traction engine I also wanted to be able to cut the wire to a constant length so also designed and built a wire cutting guillotine (I will post on HMT in another post)

Below are the photos and results of the new wire bender:

Attachment 33388
Photo of the completed tool and the first few links bent on it.

Attachment 33389 Attachment 33391 Attachment 33393
The bender forms the wire link in two stages around the pin located on the centre line of shaft. The length of wire was calculated to be 13.8mm and a datum mark was set on the shaft with a small chisel mark at approximately 7mm from the centre of fully formed link so the joint would be in the middle of link. (mark highlighted on photo).

Attachment 33394

First links fitted to each other

Attachment 33395
new link shape is a lot more pleasing on the eye (in my opinion)

Attachment 33396 Attachment 33397
Old former also didn't close the link fully.
Old link shape using nut and bolt wire bender has square ends due to the way the former was made.

As the wire is only 1mm 0.040" diameter and copper it is easy to bend.To aid the movement I didn't feel it was necessary for a handle so I simply knurled the out diameter to give grip when rotating. The Bender guide also acts as location and stops the outer from sliding all the way down the central shaft.

I am very happy with the shape and have gone into full production :p

thank you for viewing
The Home Engineer

Wow, what a difference! Nice job. :hattip:

Much better result.

Video showing the wire bender and wire guillotine to produce chain links

Hi All

I have put a video together, to show the process of making the chain links. This video shows both the wire bender and the wire guillotine.

https://www.youtube.com/watch?v=9bLw...ature=youtu.be

Many thanks
The Home Engineer

Amazing both of them.

1 Attachment(s)

first few links soldered together Attachment 33398

Firstly good on you for making your own chain instead of using ready made model chain, I was initially surprised at your use of copper but we know by now you know what you are doing. Do you plan to nickel plate or paint black?.

1 Attachment(s)

Hi olderdan
Thank you for the kind words
I did think about steel links and silver soldering. However I would have had to buy the steel and had the issue of high temperature soldering small links and then having to clean etc. The copper links are surprisingly strong as the links are very small and the tight radius helps to stiffen up the links. Another advantage is the fact I can soft solder each link with little, or should I say less chance of effecting the previous joints by controlling heat from an iron and is very clean. I my shot blast the chain and use etching primer so it has a good key and then paint. The model is also very small 1” scale and my intention is to have it mounted in a cabinet for show. The engine could be steamed but to be honest it is all about the build for me rather than steaming. It will run on compressed air when friends family etc show some interest but I expect it to stay on the shelf and I will always have a sneaky look as I walk pass, as you do when you have made something you are happy with and understand all the effort and time you have invested.
Attachment 33399
All the best
The Home Engineer

Thanks thehomeengineer! We've added your Small Wire Bender to our Metalworking category,
as well as to your builder page: thehomeengineer's Homemade Tools. Your receipt:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/homemade-small-wire-bender-2"> <img src="/uploads/229488/homemade-small-wire-bender-2.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/homemade-small-wire-bender-2">Small Wire Bender</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/bender'>bender</a>, <a href='https://www.homemadetools.net/tag/chain'>chain</a> </div> </div> </div> </div>

2 Attachment(s)

Both chains made ready for light shot blast, etched primer and paint. The chains are 220 mm (9") long and each joint soft soldered.

Attachment 33402

Thanks for the idea, making special chains for clocks, it is a simple version of the existing pneumatic tool but a lot easier to adapt for special pitch.

Congratulations thehomeengineer - your Wire Bender is the Homemade Tool of the Week!

It was nice seeing this tool go through a couple of revisions to arrive at this version.

Some more good builds from this week:

Casting Mold by celsoari
Rotary Broaching Tool by JRock
Lathe Large Dial by bobneumann
Mill Vise Stop by bouboulas
Star Knob Jig by Mazay
Welding Table Clamps by Crusty
Magnetic Sweeper by Kwandotechnic
Dog Clamps by Christofix
Flex Head Ratchet Handle by bobneumann
Post Hole Auger by tsbrownie
Kayak Skeg by rgsparber
Rounding Hammers by Philip Davies
Adjustable Roller Stand by bobs409
Door Lifter by Philip Davies
Track Saw Guide by Didpoolhall
Bench Vise by Kwandotechnic
Benchtop Grinder by mariost

thehomeengineer - you'll be receiving a $25 online gift card, in your choice of Amazon, PayPal, or bitcoin. Please PM me your current email address and gift card choice and I'll get it sent over right away.

This is your 8th Homemade Tool of the Week. Here are all of your Homemade Tool of the Week winning tools. Congrats again :thumbsup:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/claw-clamps-home-made-clamp-system-65679#post105002"> <img src="/uploads/209126/homemade-claw-clamps.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/claw-clamps-home-made-clamp-system-65679#post105002">Claw Clamps</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/clamp'>clamp</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/formers-press-tool-make-steam-lubricator-body-lid-66281#post106805"> <img src="/uploads/210255/homemade-sheetmetal-former.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/formers-press-tool-make-steam-lubricator-body-lid-66281#post106805">Sheetmetal Former</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/sheetmetal'>sheetmetal</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/ring-roller-67371#post110300"> <img src="/uploads/212750/homemade-ring-roller-33.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/ring-roller-67371#post110300">Ring Roller</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/ring-roller'>ring roller</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/axle-stands-67484#post110710"> <img src="/uploads/213175/homemade-axle-stands-3.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/axle-stands-67484#post110710">Axle Stands</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/axle'>axle</a>, <a href='https://www.homemadetools.net/tag/stand'>stand</a>, <a href='https://www.homemadetools.net/tag/jack'>jack</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/lathe-chuck-face-stop-76016#post145050"> <img src="/uploads/227488/homemade-chuck-back-and-face-stops.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/lathe-chuck-face-stop-76016#post145050">Chuck Back and Face Stops</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/chuck'>chuck</a>, <a href='https://www.homemadetools.net/tag/stop'>stop</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/small-diameter-turning-tool-360-degree-travelling-steady-76904#post148703"> <img src="/uploads/228523/homemade-small-diameter-turning-tool.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/small-diameter-turning-tool-360-degree-travelling-steady-76904#post148703">Small Diameter Turning Tool</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/threading'>threading</a>, <a href='https://www.homemadetools.net/tag/cutting-tool'>cutting tool</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/rotary-table-driven-stepper-motor-controlled-2-arduinos-77286#post150278"> <img src="/uploads/229015/homemade-arduino-controlled-rotary-table.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/rotary-table-driven-stepper-motor-controlled-2-arduinos-77286#post150278">Arduino Controlled Rotary Table</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/arduino'>Arduino</a>, <a href='https://www.homemadetools.net/tag/motor'>motor</a>, <a href='https://www.homemadetools.net/tag/controller'>controller</a> </div> </div> </div> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/forum/re-think-wire-bender-making-chain-links-77714#post151979"> <img src="/uploads/229488/homemade-small-wire-bender-2.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/forum/re-think-wire-bender-making-chain-links-77714#post151979">Small Wire Bender</a> <span> by <a href="https://www.homemadetools.net/builder/thehomeengineer">thehomeengineer</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/bender'>bender</a>, <a href='https://www.homemadetools.net/tag/chain'>chain</a> </div> </div> </div> </div>

What a great early birthday present. It is fantastic to share my projects on HMT with like minded people. I was inspired by JRock to make a rotary broaching tool and the bearings arrived today for this project so hopefully get a bit done over the weekend. . I have started another project today to help complete the Minnie Traction Engine project which I have been working on and off for 35 years and looking forward to sharing again with you all.
Thank you again
The Home Engineer

2 Attachment(s)

Hi All
I have soldered the final chain links to the steering chains eye bolts ready for painting. The eye bolts are 7BA.
Attachment 34565 Attachment 34566

The Home Engineer