RIXRIG

Just found this site while looking through PINTREST.

I'm a DIYer in northern North Carolina.
Hate to buy something (anything) if I can make it.

Rough woodworking has been my main interest; just starting some furniture type projects and some metal work.
Lots of PALLET Projects done and in the making. Finished a Greenhouse, Chicken Coop, Picket Fence for the Misses and now working on a side table for the daughter.

Just bought an anvil, a few blacksmith tools and an old rusty Rivet Forge (great blower though).
Looking to possible MAKE some garden tools for the back of my tractor (we'll see; may be over my head).

I'm not really one to 'throw anything away' because when I do I always need it the next week.
Love Crappie fishing (some Bass too)!

The site looks interesting! Looking forward to lots of browsing.

Hi RIXRIG - welcome to HomemadeTools.net :welcome:

What kind of garden tools do you want to make for your tractor?

Quote:

---

Originally Posted by Jon

Hi RIXRIG - welcome to HomemadeTools.net :welcome:

What kind of garden tools do you want to make for your tractor?

---

Thanks for the welcome. I'm looking to make an attachment for my 3 point hitch to hill rows and lay down plastic mulch at the same time. I'm going to purchase the discs themselves but, am mulling over how to make the mount for both the discs and to hold the roll of plastic mulch. As mentioned earlier I'm somewhat cheap and I do get a certain pride out of using something I make rather than buy. Example: I make my own fishing jigs, spinner baits and buzz baits and the fish I catch on them just seem to 'taste better' lol. I want our vegetables to taste the same as the fish.

Hi RIXRIG,

I had looked into building a similar rig myself, and the commercially available ones were pretty spendy, at least for my budget. There are quite a number of commercial units available to see photos to get an idea of what would be involved. Here's a good example ..

https://www.berryhilldrip.com/RB-448...ic-mulch..html

In general, what you would need to do is build a toolbar … in this case, I suggest a rectangular frame of square tubing, with the 3 point attach hardware at the front. Your actual soil working tools and plastic mulch roll holding fixturing would mount on that.

You didn't mention what category of 3 point you were working with … garden tractor hitches are generally cat 0, and small farm utility tractors are usually cat 1. The issue would be the weight of the attachment (unless you have additional support wheels on the implement) for the 3 point hitch to lift up … utility tractors being able to heft more weight to pick up the toolbar to move it to a new row.

From what you indicated, it sounds like you want to do is to raise hills, hold the mulch rolls, lay down the mulch, then cover the mulch edges with dirt. An additional function you might consider is laying down drip irrigation tape at the same time. From your intended functions, you would lay out crossmembers within the square tube rectangle to do the functions you want … first would be the bedshaping, second would be holding the roll, third would be continuously laying the mulch on the hill, and finally scooping dirt over the mulch edges to hold the plastic into place.

Googling “plastic mulch layer” brings up lots of references and pictures of commercial units, to give you an idea of how other successful units are built (reusing ideas reduces the number of prototypes I have to build and experiment with to get success). YouTube also has a good number of videos of homebuilt units that are pretty instructive on how to build one … here are a couple of my favorite links of homebuilts … first one doesn't do any bedshaping or raising …

https://www.youtube.com/watch?v=zVozkUDPVzM

second one here does radical bedshaping in the front section …

https://www.youtube.com/watch?v=P_WXgeVlT5c

and if you don't need to raise the beds, and have a low power garden tractor … here's a look at a homebuilt walk-behind tractor mulch laying unit (not 3 point, but same idea, you would just add the 3 point hitch hardware at the front of the frame) ...

https://www.youtube.com/watch?v=QD10mFBShVY

What I decided to do in my case, was to break down the bedshaping and mulching activities into two different tools. In my area, I need fairly high raised beds to get good drainage due to the high clay content of the soil. The raised bed hilling is the most labor intensive part for me, and I do that now by hand and shovel, so to expand the garden, this is most important issue for me. I have a JD 810 3 cyl diesel with a category 1 three point hitch and I recently acquired an IH Farmall 100 (just like a Super A, only it's the follow-on model) with the IH one point hitch. For next season, I intend to modify a furrower to the 1-point hitch to do the hilling, and continue to do the drip tape and mulch laying by hand. The Farmall is in the process of renovation for the job right now. Maybe a mulcher will be next, when the garden gets so large, that laying mulch by hand is too much of a chore.

In any case, I hope this helps get your ideas started. I noticed that you didn't have a welder listed in your tool inventory or acquired skills. I don't think that a wood frame would be strong enough to do bedshaping or disk work, though there probably isn't a lot of force on the tools to actually lay the mulch down, and you might get away with a wooden frame for that.

As for a welder, any old buzz-box AC welder would do … I picked one up for a song in my area, folks around here have a surplus of them as many are upgrading to MIG or inverter units …

Good luck, and keep us posted on your progress ...

Lots of very useful INFO; Thanks so much.

Nice one, piro222 :thumbsup:

Keep us posted on your progress RIXRIG.