Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 9 of 9

Thread: Rotary table

  1. #1
    Supporting Member
    Join Date
    Sep 2013
    Posts
    19
    Thanks
    3
    Thanked 67 Times in 15 Posts

    athomp's Tools

    Rotary table

    I wanted a rotary table for my mill but didn't want to have to pay big money for a decent sized one so I made my own 11" table. It's made out of 1/2" plate, 2 brake rotors and a ring gear off a lawnmower engine. I turned a spindle on the lathe and welded it to the bottom plate. A brake rotor is mounted on the spindle. Another brake rotor with the hub cut out is mounted upside down on the lower one. The ring gear is riveted to a piece of 16 gauge sheet metal and sandwiched between the two rotors. I made a worm gear on the lathe. Two thumb screws adjust the worm gear against the ring gear to eliminate backlash. There is a bolt on either side that can be screwed in against the lower brake rotor to lock the table in place. The gear ratio is a bit odd at 97:1. The whole thing weighs 123 lbs.
    Rotary table-image.jpgRotary table-image.jpgRotary table-image.jpgRotary table-image.jpgRotary table-image.jpg

    186 More Best Homemade Tools eBook
    Last edited by athomp; Jan 9, 2018 at 06:45 PM.

  2. The Following 23 Users Say Thank You to athomp For This Useful Post:

    almarghi (Sep 22, 2018), blkadder (May 17, 2018), Captainleeward (Jan 12, 2018), Gary A. Wills (Jan 13, 2018), jlrice54 (May 17, 2018), johncg (Feb 18, 2021), Kevic (Jan 3, 2019), KustomsbyKent (May 17, 2018), Miloslav (Mar 28, 2019), mwmkravchenko (May 17, 2018), Neil Jensen (Jan 10, 2018), NortonDommi (Jan 11, 2018), odd one (Feb 20, 2021), Paul Jones (Jan 12, 2018), PJs (Jan 4, 2019), SA MAKER (Mar 29, 2019), Seedtick (Jan 11, 2018), sossol (Jan 10, 2018), thehomeengineer (Jan 10, 2018), Tonyg (Mar 29, 2019), Toolmaker51 (May 19, 2018), Tule (Jan 4, 2019), volodar (Jan 4, 2019)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks athomp! We've added your Rotary Table to our Machining category,
    as well as to your builder page: athomp's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. #3
    Supporting Member
    Join Date
    Sep 2015
    Location
    Sandy, OR
    Posts
    46
    Thanks
    37
    Thanked 12 Times in 6 Posts
    Nice job! How did you mark the rotary table tick marks with..out...a ......rotary.........table?

  5. #4
    Supporting Member
    Join Date
    Sep 2013
    Posts
    19
    Thanks
    3
    Thanked 67 Times in 15 Posts

    athomp's Tools
    Quote Originally Posted by mudnducs View Post
    Nice job! How did you mark the rotary table tick marks with..out...a ......rotary.........table?
    Thanks.
    I printed out a 11" degree wheel off the Internet and glued it to the bottom of the table and then used a punch set to make the degree marks.

  6. The Following 3 Users Say Thank You to athomp For This Useful Post:

    Kevic (Jan 3, 2019), PJs (Jan 4, 2019), PTSchram (Feb 5, 2020)

  7. #5
    Supporting Member NortonDommi's Avatar
    Join Date
    Jul 2014
    Location
    North Island, New Zealand.
    Posts
    990
    Thanks
    1,800
    Thanked 524 Times in 315 Posts

    NortonDommi's Tools
    Beautiful repurposing. Looks like it could take a good load.

  8. #6
    Supporting Member blkadder's Avatar
    Join Date
    May 2012
    Location
    Florida, USA
    Posts
    168
    Thanks
    520
    Thanked 69 Times in 36 Posts
    I like this a lot. I have been curious about how to go about making one of these.
    Ron

    ...Semper Fidelis...

  9. #7
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    Sorry to have missed this first time around. Great job on a big project, not to mention effective design incorporating unmatched components. Have to mention rotary tables/ indexers are my first line answer to tricky contours and spacing.
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  10. The Following User Says Thank You to Toolmaker51 For This Useful Post:

    PJs (Jan 4, 2019)

  11. #8
    Supporting Member Radioman's Avatar
    Join Date
    Jun 2018
    Location
    Massachusetts
    Posts
    209
    Thanks
    11
    Thanked 87 Times in 53 Posts

    Radioman's Tools
    Nice work. Would love to see some of the worm gear turning? Also how you got the lawn mower ring gear mounted and in mesh with the home built worm?

  12. The Following User Says Thank You to Radioman For This Useful Post:

    PJs (Jan 4, 2019)

  13. #9
    Supporting Member bobneumann's Avatar
    Join Date
    Jul 2018
    Posts
    40
    Thanks
    1
    Thanked 196 Times in 31 Posts

    bobneumann's Tools
    Nice looking!. Where did you get the actual table portion? Did you machine it yourself?
    And how much rocking deflection do you get under a heavy load? It seems like three roller bearings mounted underneath the perimeter of the lower rotor would prevent it from rocking.



    186 More Best Homemade Tools eBook
    Last edited by bobneumann; Jan 30, 2019 at 09:10 AM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •