Shop Built Tubing Straightener

Using NiCop coiled brake line is pain only in trying to get it straight. I couldn't make myself spend 200 dollars on a 5 roller tubing straightener so I designed one in 3D CAD and built it in the shop.
I turned the rollers with a Vee Groove which will work with any size tubing up to 5/8th's of an inch. it works especially well with 3/16th's to 3/8th line.
This is the business side of the rig showing the five rollers.
http://images43.fotki.com/v61/photos...3/photo-vi.jpg
I still need to weld up the top plate but I did a proof of design and it works great!
Here is the back showing the adjustment block which carries the two upper rollers on some shoulder bolts.
http://images61.fotki.com/v249/photo.../photo1-vi.jpg
Once I finish the welding this bolt will get cut down and the tensioning knob will be attached to it.
http://images20.fotki.com/v113/photo...3/photo-vi.jpg
Turn the knob to raise or lower the rollers to fit the tube you are straightening and to set the tension on the tube as you straighten it.
This is a pic of some of the pieces. The five rollers, tensinong knob and block and the trunnion I made so the aluminum block wouldn't have to be threaded. The trunnion carries all of the tensioning loads.
http://images61.fotki.com/v249/photo...7/photo-vi.jpg
I'll post up pics after i get it welded and painted.
Mark

great idea! so much easier than straightening out new brake Ad fuel lines with a rubber mallet on the floor.

Thanks Mark! I've added your Tubing Straightener to our Tube Benders category, as well as to your builder page: astroracer's Homemade Tools. Your receipt:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="/tubing-straightener"><img src="/uploads/112462/tubing-straightener.jpeg" alt="Tubing Straightener" /></a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="/tubing-straightener">Tubing Straightener</a> <span> by <a href="/builder/astroracer_2">astroracer</a></span> </div> <div class="tags"> tags: <a href="/tag/tubing">tubing</a>, <a href="/tag/straight">straight</a> </div> </div> </div> </div>

Great build. I agree with Ron, this is a great way to straighten tubing.

I FINALLY got around to finishing up the Straightener! I got it all welded together anfd painted over this past weekend and assembled it today.
Getting some bright red paint. This is rattlecan Rustoleum Bright Red over their grey primer.
http://images60.fotki.com/v661/photo...MVC022F-vi.jpg
I had to finish up a couple of other items to get this done. One was drilling and tapping the tensioning knob for a set screw to lock it to the tensioning rod.
http://images56.fotki.com/v127/photo...MVC002F-vi.jpg
I made the tensioning rod out of a piece of 3/8-16 all thread. Here you can see it installed in the roller block. I used a cheap drill bit depth stop collar to trap the rod so the block will move up and down as the knob is turned.
http://images58.fotki.com/v85/photos...MVC009F-vi.jpg

Looks pretty good with everything assembled.
http://images55.fotki.com/v605/photo...MVC011F-vi.jpg

Continued in next post.

I kinked up a piece of tubing to try it out.
http://images55.fotki.com/v648/photo...MVC006F-vi.jpg

After a few runs through the straightener this was like an arrow again. :)
http://images55.fotki.com/v648/photo...MVC007F-vi.jpg
I'm very happy with the results! the straightener works great!
http://images56.fotki.com/v168/photo...MVC008F-vi.jpg
Mark

nice work!

Very, very nice. I kinked my share of aluminum tubing years ago on my airplane project and could've used a straightener just like this. I'm sure it'll serve you well. :thumbsup:

Ken

Wow that is neat, Thanks for posting!!

Ralph

can you make a similar system using a vice

Are you just pulling the tube through the straightener by hand?

Ralph

https://www.youtube.com/watch?v=pLpIgD3Rp1g

Are plans available?