Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 3 of 3

Thread: Re-think, pulley tension adjustment for bead roller and slip rollers

  1. #1
    Supporting Member thehomeengineer's Avatar
    Join Date
    Nov 2017
    Location
    Berkshire UK
    Posts
    704
    Thanks
    720
    Thanked 2,062 Times in 406 Posts

    thehomeengineer's Tools

    Re-think, pulley tension adjustment for bead roller and slip rollers

    Hi All

    After receiving the vee-belts in the post I soon realised the eccentric plummer block would not offer enough adjustment to tension both belts. So a re-think was needed and a solution to this problem.

    I decided to manufacture a hinge plate the plummer block could be bolted too and operated via a single screw to tension the belts in conjunction with the motor adjustment and the eccentric plummer block. The eccentric was also difficult to adjust so a handle was made to rotate the shaft.

    Link to previous post.
    Powering homemade sheet metal tooling (Table and motor arrangement)

    The photos below show the solution.

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4382-painted.jpg
    Painted components ready for assembly

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4385-4-jaw-setup.jpg Re-think, pulley tension adjustment for bead roller and slip rollers-img_4386-machined.jpg
    Eccentric casting housing machined to accept operating lever.

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4387-drilling-handle.jpg
    handle drilled and tapped at angle to give clearance on plummer block body. This tapped hole also locks the handle to casting.

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4392-simple-hinge.jpg
    The base plate was made from 6mm aluminium and the hinge was made from another piece of 6mm plate bolted together and drilled on joint center line to accept 8mm pin.

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4389-part-assembled.jpg
    Screw showing additional adjustment

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4388-ready-eccentric.jpg
    Ready for final assembly

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4393-pulley-side.jpg Re-think, pulley tension adjustment for bead roller and slip rollers-img_4394-eccentric-lever-side.jpgRe-think, pulley tension adjustment for bead roller and slip rollers-img_4391-completed-assembly.jpg
    Fully assembled

    Re-think, pulley tension adjustment for bead roller and slip rollers-img_4396-position.jpg Re-think, pulley tension adjustment for bead roller and slip rollers-img_4395-linked-motor.jpg
    Bolted to underside of table top

    After setting up, the belts can be tensioned relatively easy and a new length belt for the bead roller is need as the one i purchased is to short but the slip rolls worked out a treat and have had them rotating via the drive.

    New belt on order for bead roller.

    Thank you for viewing
    Thw Home Engineer

    186 More Best Homemade Tools eBook

  2. The Following 7 Users Say Thank You to thehomeengineer For This Useful Post:

    baja (Jan 28, 2020), Christophe Mineau (Jan 27, 2020), high-side (Jan 27, 2020), Jon (Jan 27, 2020), Philip Davies (Jan 28, 2020), Scotsman Hosie (Feb 2, 2020), threesixesinarow (Jan 27, 2020)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks thehomeengineer! We've added your Pulley Tension Adjuster to our Miscellaneous category,
    as well as to your builder page: thehomeengineer's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. #3
    Supporting Member Philip Davies's Avatar
    Join Date
    Dec 2015
    Location
    Reading, Berks, UK
    Posts
    868
    Thanks
    1,184
    Thanked 1,018 Times in 342 Posts

    Philip Davies's Tools
    This is definitely far superior to hinging the motor to allow gravity to tension the belt!



    186 More Best Homemade Tools eBook

  5. The Following User Says Thank You to Philip Davies For This Useful Post:

    thehomeengineer (Jan 28, 2020)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •