Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: A Drop-In Bench Vise Jaw Jack

  1. #1
    Supporting Member rgsparber's Avatar
    Join Date
    Nov 2012
    Location
    Phoenix, AZ
    Posts
    1,277
    Thanks
    733
    Thanked 2,758 Times in 649 Posts

    rgsparber's Tools

    A Drop-In Bench Vise Jaw Jack

    Sometimes I need to clamp a small piece of stock at one end of my bench vise. Without adding any packing to the other end, the jaws tilt resulting in poor clamping action. Adding packing of exactly the right thickness solves that problem. But I don't always have such packing. One solution is a variable thickness packing block or… a Jaw Jack.

    If you are interested, please see

    https://rick.sparber.org/DropInJawJack.pdf


    Your comments are welcome. All of us are smarter than any one of us.


    Thanks,

    Rick

    186 More Best Homemade Tools eBook
    Rick

  2. The Following 5 Users Say Thank You to rgsparber For This Useful Post:

    Jon (Feb 21, 2020), Little Rabbit (Feb 20, 2020), oldpastit (Feb 21, 2020), verticalmurph (Feb 20, 2020), will52100 (Feb 20, 2020)

  3. #2
    Supporting Member madokie's Avatar
    Join Date
    Oct 2017
    Posts
    165
    Thanks
    1
    Thanked 53 Times in 46 Posts
    pass ,,,too complicated and parts to loose,, how about a dozen 5/8 flat washers stacked on top of each other and loosely riveted or bolted together, at the far edge away from the center hole.. u just put how ever many washers u need to hold the gap open and u can run a thick wire or rod through center hole on top of vise jaws to keep washers in place while u hold other part and tighten vise..

    2000 Tool Plans
    Last edited by madokie; Feb 20, 2020 at 05:43 PM.

  4. The Following User Says Thank You to madokie For This Useful Post:

    mklotz (Feb 21, 2020)

  5. #3
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,433
    Thanks
    357
    Thanked 6,370 Times in 2,116 Posts

    mklotz's Tools
    Quote Originally Posted by madokie View Post
    pass ,,,too complicated and parts to loose,, how about a dozen 5/8 flat washers stacked on top of each other and loosely riveted or bolted together, at the far edge away from the center hole.. u just put how ever many washers u need to hold the gap open and u can run a thick wire or rod through center hole on top of vise jaws to keep washers in place while u hold other part and tighten vise..
    Thank you for your post.

    Sometime ago I acquired more brass key tags than I will ever need and so decided to make an adjustable spacer with them...

    A Drop-In Bench Vise Jaw Jack-spacer2.jpg

    I've used it numerous times on my milling block...

    A Drop-In Bench Vise Jaw Jack-spacer1.jpg

    but, now, with the benefit of your post, I realize it would work perfectly as an adjustable vise shim.
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  6. The Following 4 Users Say Thank You to mklotz For This Useful Post:

    bobs409 (Feb 23, 2020), jdurand (Feb 21, 2020), Jon (Feb 21, 2020), rgsparber (Feb 21, 2020)

  7. #4
    Supporting Member madokie's Avatar
    Join Date
    Oct 2017
    Posts
    165
    Thanks
    1
    Thanked 53 Times in 46 Posts
    good ,,just what i was thinking ..

  8. #5
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,057
    Thanks
    771
    Thanked 1,850 Times in 1,652 Posts


    Thanks mklotz! We've added your Adjustable Vise Shim to our Vises category,
    as well as to your builder page: mklotz's Homemade Tools. Your receipt:




  9. #6
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,057
    Thanks
    771
    Thanked 1,850 Times in 1,652 Posts


    Thanks rgsparber! We've added your Adjustable Bench Vise Jaw Jack to our Vises category,
    as well as to your builder page: rgsparber's Homemade Tools. Your receipt:




  10. #7
    Supporting Member rgsparber's Avatar
    Join Date
    Nov 2012
    Location
    Phoenix, AZ
    Posts
    1,277
    Thanks
    733
    Thanked 2,758 Times in 649 Posts

    rgsparber's Tools
    I realized from "madokie" and Marv's comments that I had not fully explained the purpose and how to use the jack. My goal is to have packing for the vise that prevents any tilting over a range of stock thicknesses. A stack of disks nicely solves the problem of getting close to a given thickness but, on average, will permit a tilt equal to 1/2 the thickness of a disk (assuming they are all the same thickness).

    The stack of packing plus the jack solves the problem. But since I don't have a stack of disks and am always looking for alternate ways to do anything, I made a stack of blocks with a binary ratio of thicknesses: 0.5", 0.25", 0.125", and 0.063". The jack takes up 0.375" to about 0.5". This means I can create any exact thickness from 0.375" to about 1.4" and never use more than 5 pieces.

    I'll update the article with proper acknowledgments.

    Thanks,

    Rick
    Last edited by rgsparber; Feb 22, 2020 at 12:10 PM.
    Rick

  11. #8
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,433
    Thanks
    357
    Thanked 6,370 Times in 2,116 Posts

    mklotz's Tools
    You're absolutely correct about the stack permitting a slight tilt proportional to half the disk thickness. Fortunately the disks are thin and my aged vise is very sloppy.

    My compliments on having the insight to use a binary progression of spacers. I've been advocating that for a long time. As an example, DI extenders often come in a threesome of 1, 2, 3" sizes, which permits all the inch integer combinations up to 6"...

    1 = 1
    2 = 2
    3 = 3
    4 = 1 + 3
    5 = 2 + 3
    6 = 1 + 2 + 3

    but a binary threesome of 1, 2, 4" sizes permits all the combinations up to 7"

    1 = 1
    2 = 2
    3 = 1 + 2
    4 = 4
    5 = 1 + 4
    6 = 2 + 4
    7 = 1 + 2 + 4

    In a foursome of spacers, the difference becomes greater.

    1 + 2 + 3 + 4 = 10
    1 + 2 + 4 + 8 = 15

    and similarly for larger collections.

    Also, in binary collections with more members one has the advantage of simply writing the desired size in binary to determine which spacers to use.
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  12. The Following User Says Thank You to mklotz For This Useful Post:

    Little Rabbit (Feb 24, 2020)

  13. #9
    Supporting Member madokie's Avatar
    Join Date
    Oct 2017
    Posts
    165
    Thanks
    1
    Thanked 53 Times in 46 Posts
    exactly,, use a stack of washers with different thicknesses, to get your desired size, u can also use a short NF bolt(face off bolt head in lathe) and 2 nuts,run one nut (standard lenght or get a longer nut )to the end of bolt and use the second nut as a jam nut,u should be able to get your size easily within 010,, just use a magnet to hold bolt in place on vise..another way to do this is to drill and tap a hole all the way through vise and jaws and use a long bolt with a jam nut, a bit labor involved, but if your going to do this a lot..now if your going to be doing a lot of the same size parts , get a extra pair of small milling step jaw clamping height blocks and machine to size..or just make up some spacers to your needed size..
    Last edited by madokie; Feb 22, 2020 at 02:06 PM.

  14. The Following User Says Thank You to madokie For This Useful Post:

    Little Rabbit (Feb 24, 2020)

  15. #10
    Supporting Member rgsparber's Avatar
    Join Date
    Nov 2012
    Location
    Phoenix, AZ
    Posts
    1,277
    Thanks
    733
    Thanked 2,758 Times in 649 Posts

    rgsparber's Tools
    The design has not finished evolving. I found a box of old lock parts that were perfect for making a stack of equal thickness bars. I really like how the bars fill the gap between the fixed vise jaw and the jack. They naturally filled this gap by flopping down. Although it has a lot more parts, it is much easier to use without having to think much about it. The article has been updated with this iteration. Proof, again, that we should never throw any metal away. Also proof that all of us are smarter than any one of us.

    Rick
    Rick

  16. The Following User Says Thank You to rgsparber For This Useful Post:

    Little Rabbit (Feb 24, 2020)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •