Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12

Thread: Leg vise from junk

  1. #1
    Supporting Member Tuomas's Avatar
    Join Date
    Jun 2016
    Location
    Jyväskylä Finland
    Posts
    832
    Thanks
    558
    Thanked 1,834 Times in 507 Posts

    Tuomas's Tools

    Leg vise from junk

    Made a diy leg vise from junk / surplus that i could found.



    Its not a beauty, but works for me.

    Traditionally leg vises are based to threaded rod with a big diameter, that supports / alings vise straight. Some extra guidance can be get with dowels etc..

    But, big screw is the "main" thing.
    Those are just hard to find for cheap.
    I wanted to found alternative way to make a leg vise.

    If you watched the video, you might notice, i didn't need to use any extra supports on the long end of the clamped piece. Vise holds well and is easy to make.

    186 More Best Homemade Tools eBook
    Last edited by Tuomas; Jul 3, 2020 at 08:24 AM.

  2. The Following 8 Users Say Thank You to Tuomas For This Useful Post:

    bruce.desertrat (Jul 3, 2020), DIYer (Jul 3, 2020), Drew1966 (Jul 3, 2020), Jon (Jul 6, 2020), Priemsy (Jul 3, 2020), sossol (Jul 3, 2020), tommyhill (Jul 6, 2020), Toolmaker51 (Jul 4, 2020)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,057
    Thanks
    771
    Thanked 1,850 Times in 1,652 Posts


    Thanks Tuomas! We've added your Leg Vise to our Vises category,
    as well as to your builder page: Tuomas's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. #3
    Supporting Member bruce.desertrat's Avatar
    Join Date
    Nov 2017
    Posts
    782
    Thanks
    553
    Thanked 665 Times in 357 Posts

    bruce.desertrat's Tools
    Those are, I assume, OSHA certified steel-toed safety socks in that last bit :-) I think I should go prowling for a couple of old car jacks...

  5. #4
    Supporting Member Drew1966's Avatar
    Join Date
    Oct 2016
    Posts
    457
    Thanks
    517
    Thanked 144 Times in 89 Posts
    Nice. Definitely not a carpenter’s vise, but a good, solid build. Good job.

  6. #5
    Supporting Member Tuomas's Avatar
    Join Date
    Jun 2016
    Location
    Jyväskylä Finland
    Posts
    832
    Thanks
    558
    Thanked 1,834 Times in 507 Posts

    Tuomas's Tools
    Quote Originally Posted by bruce.desertrat View Post
    Those are, I assume, OSHA certified steel-toed safety socks in that last bit :-) I think I should go prowling for a couple of old car jacks...
    My friend says that i am weird.. but i have a reason not to wear shoes on the shop.

    These: Leg vise from junk-fb_img_1593839178920.jpg

    I "have to!" keep floors clean from the sharp depris etc.
    When walking on the floor starts to feel uncomfortable, its time to clean.
    Last edited by Tuomas; Jul 3, 2020 at 11:15 PM.

  7. #6
    Supporting Member Tuomas's Avatar
    Join Date
    Jun 2016
    Location
    Jyväskylä Finland
    Posts
    832
    Thanks
    558
    Thanked 1,834 Times in 507 Posts

    Tuomas's Tools
    Quote Originally Posted by Drew1966 View Post
    Nice. Definitely not a carpenter’s vise, but a good, solid build. Good job.
    Thanks.

  8. #7
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    The heavy forged leg vises depend on a hinge at lower edge. Suddenly that causes wonder how they expect parallel clamping with that fixed point, though the jaw faces are far narrower then Tuomas's. There is no dispute his version works well on various thicknesses. And just like strap clamps for milling, the leverage is correct with tightening closer to jaws. Cannibalization of the screw jack, especially nut and thread is a super economical supply of sturdy material. Using all of it is perfection.
    Unless you treasure rivets...
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  9. #8
    Supporting Member Drew1966's Avatar
    Join Date
    Oct 2016
    Posts
    457
    Thanks
    517
    Thanked 144 Times in 89 Posts
    Quote Originally Posted by Toolmaker51 View Post
    The heavy forged leg vises depend on a hinge at lower edge. Suddenly that causes wonder how they expect parallel clamping with that fixed point, though the jaw faces are far narrower then Tuomas's. There is no dispute his version works well on various thicknesses. And just like strap clamps for milling, the leverage is correct with tightening closer to jaws. Cannibalization of the screw jack, especially nut and thread is a super economical supply of sturdy material. Using all of it is perfection.
    Unless you treasure rivets...
    Toolmaker, those heavy leg vises with the hinge at the bottom are a blacksmithing tool. Carpenters leg vises have always had some sort of mechanism to hold the faces close to parallel, sometimes heavy dowels, sometimes a cross mechanism and sometimes a simple wedge system.

  10. #9
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,330
    Thanks
    7,041
    Thanked 2,977 Times in 1,892 Posts

    Toolmaker51's Tools
    Agreed, Drew1966. I don't recall leg vises that weren't associated with blacksmithing. Mechanically speaking, that seems to counter best possible grip on parts; of jaws engaged flat on material. I've considered fabricating a leg vise over the years, with a notched link versus hinge. Tuomas's compression springs are a great solution.

    With some bit of a thread hack;
    Mentoring potential machinists, getting to discussions on machinery setup, I rely on a quick demonstration of leverage. Sketching it out is not effective. Some few decades now, the ability to grasp simple, unalterable principals has waned.

    "Put your index fingers flat on the table, about this far apart [using a wood pencil]".
    I lay pencil across their fingers and thumb the middle. Then I move thumb closer to one of their fingers, and press the same amount.
    "So what position of the clamping stud is going to hold more securely?"
    They get it every time.
    Having them arrive at concept the strap must pinch at the end or be flat, takes a little more convincing.
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  11. #10
    Supporting Member Drew1966's Avatar
    Join Date
    Oct 2016
    Posts
    457
    Thanks
    517
    Thanked 144 Times in 89 Posts
    If you have a look at the Pask Makes channel on YouTube, he’s done a pretty classical carpenters leg vise.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •