Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 5 of 5

Thread: Titivating a miniature chop saw

  1. #1
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,433
    Thanks
    357
    Thanked 6,378 Times in 2,116 Posts

    mklotz's Tools

    Titivating a miniature chop saw

    I use this miniature chop saw often while building models. I added two improvements to it that make it easier to use.

    As built, there is no indicator to show where the blade will touch down on the material being sawn. Trying to hold your head flat on the bench and squinting under the descending saw is at best uncomfortable and looks damn silly. My fix was to cement a thin strip of wood to the fixed jaw of the vise; once dry I simply dropped the saw and cut it off. Now I have a very visible indicator to show where the blade will strike the stock held in the vise.

    Titivating a miniature chop saw-chop-1.jpg

    Many of my jobs, such as the miniature saw horses in the pictures, require cutting a number of pieces to the same length. This would be a lot easier to do if the saw at a stop against which to place the stock so each cut is the same length. I puzzled over how to build a simple stop until I disabused myself of the idea that the stop had to be parallel to the vise jaws (as is the case for a horizontal band saw). In the base of my saw were two holes meant to be used to screw the saw to a bench or whatever. It was a simple job to enlarge these holes and tap them 6 x 1 mm. Then a chunk of 1/2 x 1/2 wood was drilled so it can be clamped on the outfeed table. It was made long enough so it can be used as a stop when the vise is rotated to different angles.

    Titivating a miniature chop saw-chop-2.jpg

    Probably fifteen minutes of work to make a good tool a lot more pleasant to use.

    186 More Best Homemade Tools eBook
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  2. The Following 3 Users Say Thank You to mklotz For This Useful Post:

    Home-PC (May 14, 2021), Moby Duck (May 11, 2021), Paul Jones (May 11, 2021)

  3. #2
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 442 Times in 180 Posts

    old_toolmaker's Tools
    Marv,
    A very quick and handy cutting aid. That was an issue just waiting for a solution.

    2000 Tool Plans
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

  4. #3
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks mklotz! We've added your Mini Chop Saw Modifications to our Model Making category,
    as well as to your builder page: mklotz's Homemade Tools. Your receipt:




  5. #4

    Join Date
    Feb 2019
    Posts
    151
    Thanks
    62
    Thanked 98 Times in 54 Posts
    Nice straightforward mod to that little saw. I like the cut line indicator, so simple and effective. Some version of that would be useful on any similar cut-off machine. I'll probably add something like that to my old power hacksaw. Much easier than lowering the blade to see where it touches the stock while sliding the stock back and forth trying to line it up and then clamping it, a process that takes at least three hands.

    Marv your posts are almost always something of a high-water mark around here. I always make a point to read them because even if the subject of the post is not something I am specifically interested in there is a high probability that I will, at the very least, learn a new word-of-the-day. Thanks!

  6. The Following User Says Thank You to clavius For This Useful Post:

    mklotz (May 9, 2021)

  7. #5
    Supporting Member mklotz's Avatar
    Join Date
    Aug 2015
    Location
    LA, CA, USA
    Posts
    3,433
    Thanks
    357
    Thanked 6,378 Times in 2,116 Posts

    mklotz's Tools
    Quote Originally Posted by clavius View Post
    ...
    Marv your posts are almost always something of a high-water mark around here. I always make a point to read them because even if the subject of the post is not something I am specifically interested in there is a high probability that I will, at the very least, learn a new word-of-the-day. Thanks!
    Thanks for the kind words. I try to keep my writing efforts helpful and concise (although my wife thinks I fail on the latter). Languages are something of a hobby for me and yes, I'm a stickler for spelling and grammar.

    As for interesting words, here are a few useful for shop work...


    antigodlin - lopsided or at an angle; out of alignment

    bricolage - something constructed using whatever was available at the time

    lethologica - the inability to remember the right word

    lethonomia - the inability to recall the right name

    nugatory - of no real value; trifling; worthless

    oniomania - an uncontrollable desire to buy things

    titivate - make small improvements to


    and here are a few that are useful when describing the people with whom you interact...


    cunctator - procrastinator; delayer

    logorrhea - excessive talkativeness

    ultracrepidarian - noting or pertaining to a person who criticizes, judges, or gives advice outside the area of his or her expertise



    186 More Best Homemade Tools eBook
    ---
    Regards, Marv

    Home Shop Freeware
    https://www.myvirtualnetwork.com/mklotz

  8. The Following 3 Users Say Thank You to mklotz For This Useful Post:

    clavius (May 9, 2021), Moby Duck (May 11, 2021), Shaper (May 11, 2021)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •