Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14

Thread: Extra low profile milling clamps

  1. #1
    Raytonian's Avatar
    Join Date
    Apr 2018
    Posts
    12
    Thanks
    15
    Thanked 41 Times in 5 Posts

    Raytonian's Tools

    Extra low profile milling clamps

    Randy Richard's post on YouTube inspired me to go further, making even lower profile clamps for not only just being able to clamp ridiculously thin stock to the bed but in addition to that, totally disappear into the T-slot when not needed. They are so low, they can be pushed to the other side of the table, under the vise when you're desperate enough. The clamped stock shown is 3mm plate which is probably less than practical.
    While my modification of Randy's version is not to his level of detail, with my method, there's no need for slotting the toggles as the pins allow the clamping bolts to swivel to the clamping angle.
    My dimensions are for the Bridgeport table and will of course have to be adapted for different slot dimensions. Bolt lengths are to be decided upon in practice and cut to optimum lengths.

    My sincere apologies if this was already done before as I've never seen it anywhere before and was to me, an original idea in my small world of reference.
    So please don't post if it already exists.
    Great fun to all of you who happens to find it useful!!

    Extra low profile milling clamps-img1.jpg Extra low profile milling clamps-img_2.jpg Extra low profile milling clamps-img_3.jpg
    Extra low profile milling clamps-img_4.jpg Extra low profile milling clamps-img_5.jpg Extra low profile milling clamps-img_6.jpg
    Low profile clamp.PDF

    186 More Best Homemade Tools eBook

  2. The Following 25 Users Say Thank You to Raytonian For This Useful Post:

    albertq (Jan 21, 2024), asterix (Sep 19, 2021), bilbo88 (Jan 21, 2022), BuffaloJohn (Sep 18, 2021), butlerandrew (Jan 19, 2023), Christophe Mineau (Sep 14, 2021), cognitdiss (Sep 14, 2021), Dimsa (Sep 20, 2021), DIYSwede (Sep 15, 2021), flyfr8rs (Sep 20, 2021), Home-PC (Sep 17, 2021), Jon (Sep 14, 2021), jpmacdowell (Sep 22, 2021), kboy0076 (Sep 19, 2021), metric_taper (Sep 19, 2021), Moldyjim (Sep 15, 2021), nova_robotics (Sep 18, 2021), Saltfever (Sep 15, 2021), schuylergrace (Sep 14, 2021), Sleykin (Sep 14, 2021), techcollect (Sep 20, 2021), that_other_guy (Oct 1, 2021), Toolmaker51 (Sep 23, 2021), uv8452 (Sep 16, 2021), WmRMeyers (Sep 15, 2021)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,057
    Thanks
    771
    Thanked 1,850 Times in 1,652 Posts


    Thanks Raytonian! We've added your Low Profile Milling Clamps to our Clamps category,
    as well as to your builder page: Raytonian's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. #3
    Supporting Member Christophe Mineau's Avatar
    Join Date
    Jul 2014
    Location
    France, Brittany !
    Posts
    910
    Thanks
    823
    Thanked 1,672 Times in 479 Posts

    Christophe Mineau's Tools
    Great idea, thanks for sharing !
    What's the use of the through hole on the rounded end of the claw ?
    What angles did you give to the other end ?
    Cheers !
    Christophe
    ________________________________________________________________
    Visit my Website : http://www.labellenote.fr/
    Facebook : La Belle Note
    All my personal works, unless explicitly specified, are released under
    Creative Commons BY-NC-SA license.

  5. #4
    Supporting Member Saltfever's Avatar
    Join Date
    Apr 2012
    Location
    NorCal
    Posts
    343
    Thanks
    389
    Thanked 123 Times in 84 Posts

    Saltfever's Tools
    "How low can you go" . . . I think you have won! I have never seen anything that can totally disappear into the T-slot when not needed. Thanks for posting a great idea.

    PS: are the thru holes the pivot point for rounding the ends?
    Last edited by Saltfever; Sep 15, 2021 at 01:31 AM.

  6. The Following User Says Thank You to Saltfever For This Useful Post:

    WmRMeyers (Sep 15, 2021)

  7. #5
    Supporting Member WmRMeyers's Avatar
    Join Date
    Dec 2014
    Posts
    883
    Thanks
    402
    Thanked 366 Times in 252 Posts

    WmRMeyers's Tools
    Quote Originally Posted by Raytonian View Post
    Randy Richard's post on YouTube inspired me to go further, making even lower profile clamps for not only just being able to clamp ridiculously thin stock to the bed but in addition to that, totally disappear into the T-slot when not needed. They are so low, they can be pushed to the other side of the table, under the vise when you're desperate enough. The clamped stock shown is 3mm plate which is probably less than practical.
    While my modification of Randy's version is not to his level of detail, with my method, there's no need for slotting the toggles as the pins allow the clamping bolts to swivel to the clamping angle.
    My dimensions are for the Bridgeport table and will of course have to be adapted for different slot dimensions. Bolt lengths are to be decided upon in practice and cut to optimum lengths.

    My sincere apologies if this was already done before as I've never seen it anywhere before and was to me, an original idea in my small world of reference.
    So please don't post if it already exists.
    Great fun to all of you who happens to find it useful!!
    I'm going to have to see if I can miniaturize these. My milling machines are all desktop devices, with the largest being quite a bit smaller than a Bridgeport. A 5/8" T-nut is about twice as large as is needed, and maybe more.

    Bill

  8. #6
    Raytonian's Avatar
    Join Date
    Apr 2018
    Posts
    12
    Thanks
    15
    Thanked 41 Times in 5 Posts

    Raytonian's Tools
    Exactly that. I had to make use of the hole because my rotary table's back plate (bought second hand) is totally out of true which rendered it useless. Still on the cards as a future project, bringing it up to standard.

  9. The Following 2 Users Say Thank You to Raytonian For This Useful Post:

    Christophe Mineau (Sep 15, 2021), Saltfever (Sep 16, 2021)

  10. #7
    Raytonian's Avatar
    Join Date
    Apr 2018
    Posts
    12
    Thanks
    15
    Thanked 41 Times in 5 Posts

    Raytonian's Tools
    The angles are indicated in the attached PDF file.

  11. The Following 3 Users Say Thank You to Raytonian For This Useful Post:

    Christophe Mineau (Sep 15, 2021), that_other_guy (Oct 1, 2021), WmRMeyers (Sep 15, 2021)

  12. #8
    Raytonian's Avatar
    Join Date
    Apr 2018
    Posts
    12
    Thanks
    15
    Thanked 41 Times in 5 Posts

    Raytonian's Tools
    Quote Originally Posted by Christophe Mineau View Post
    Great idea, thanks for sharing !
    What's the use of the through hole on the rounded end of the claw ?
    What angles did you give to the other end ?
    My previous attempt to reply went somewhere and I'd just like to confirm that the through hole was a guide for manually shaping the outside radius on the claw. The angles are indicated on the PDF drawing. (bottom of the pictures.

  13. #9
    Supporting Member Christophe Mineau's Avatar
    Join Date
    Jul 2014
    Location
    France, Brittany !
    Posts
    910
    Thanks
    823
    Thanked 1,672 Times in 479 Posts

    Christophe Mineau's Tools
    Quote Originally Posted by Raytonian View Post
    My previous attempt to reply went somewhere and I'd just like to confirm that the through hole was a guide for manually shaping the outside radius on the claw. The angles are indicated on the PDF drawing. (bottom of the pictures.
    Yes , it's OK, I didn't see the pdf at first sight
    Great work !
    Christophe
    Cheers !
    Christophe
    ________________________________________________________________
    Visit my Website : http://www.labellenote.fr/
    Facebook : La Belle Note
    All my personal works, unless explicitly specified, are released under
    Creative Commons BY-NC-SA license.

  14. #10
    Raytonian's Avatar
    Join Date
    Apr 2018
    Posts
    12
    Thanks
    15
    Thanked 41 Times in 5 Posts

    Raytonian's Tools
    I'm really surprised and very much appreciate the number of 'thank you's' I received and which are still coming in.
    Thanks to YOU guys!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •