Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: Vacuum tube tester - photo

  1. #1
    Content Editor
    Supporting Member
    Altair's Avatar
    Join Date
    Aug 2013
    Posts
    11,727
    Thanks
    1,353
    Thanked 29,258 Times in 9,724 Posts

    186 More Best Homemade Tools eBook

  2. The Following User Says Thank You to Altair For This Useful Post:

    baja (Jun 21, 2020)

  3. #2
    Supporting Member jdurand's Avatar
    Join Date
    May 2019
    Location
    Krasnodar Krai, Russian Federation
    Posts
    1,456
    Thanks
    126
    Thanked 742 Times in 416 Posts

    jdurand's Tools
    remember the free standing ones in the electronics stores where you could test your tubes to see if you needed new ones? Also test the new ones you just bought.

    2000 Tool Plans

  4. The Following 3 Users Say Thank You to jdurand For This Useful Post:

    bruce.desertrat (Jun 20, 2020), N00b Machinist (Jun 20, 2020), Scotty12 (Jun 20, 2020)

  5. #3
    Supporting Member
    Join Date
    May 2016
    Posts
    112
    Thanks
    52
    Thanked 31 Times in 21 Posts
    I remember them. Couldn’t tell you where. Too early for Radio Shack. Lafayette Electronics, maybe?

  6. #4
    Supporting Member Crusty's Avatar
    Join Date
    May 2019
    Location
    Dry Gulch, Tx
    Posts
    749
    Thanks
    220
    Thanked 845 Times in 324 Posts

    Crusty's Tools
    Tube testers were in the supermarkets up til the mid 60's. I remember my dad taking all the tubes out of the tv, checking them on the tester at the grocery store and buying replacements for the ones that were gone or about to go.

    That was know as Hollow State technology (the remnants of a bygone civilization of which there is no longer anyone alive that understands them).
    If you can't make it precise make it adjustable.

  7. The Following User Says Thank You to Crusty For This Useful Post:

    N00b Machinist (Jun 28, 2020)

  8. #5
    Supporting Member Beserkleyboy's Avatar
    Join Date
    Aug 2014
    Location
    Sunny South Coast NSW, Australia
    Posts
    366
    Thanks
    473
    Thanked 226 Times in 132 Posts

    Beserkleyboy's Tools
    ...plenty of Marshall valve amps available new...Oh and my local small appliance repair shop in Nowra, NSW, still has a similar tester in the workshop! I asked them and they told me you'd be surprised how many valve/tube devices are still out there...cheers
    Last edited by Beserkleyboy; Jun 20, 2020 at 06:10 PM.

  9. #6
    Supporting Member IntheGroove's Avatar
    Join Date
    May 2019
    Location
    Lake Tahoe
    Posts
    1,908
    Thanks
    181
    Thanked 852 Times in 517 Posts

    IntheGroove's Tools
    About those free standing units. Many of them were found to be rigged to flag a tube as bad when in fact it was good. And as a kid I thought something was wrong when my tube was "bad" and all of the new ones in the box were also "bad". I can't find the whole story but some of you might remember that...

  10. #7
    Supporting Member TrickieDickie's Avatar
    Join Date
    Jun 2018
    Location
    Louisiana
    Posts
    457
    Thanks
    23
    Thanked 121 Times in 93 Posts
    I remember seeing them at the Radio Shack stores and of course more professional electric suppliers

  11. #8
    Supporting Member bruce.desertrat's Avatar
    Join Date
    Nov 2017
    Posts
    785
    Thanks
    557
    Thanked 667 Times in 357 Posts

    bruce.desertrat's Tools
    The local drug store had one, with a full complement of replacement tubes underneath. My electronics teacher in HS used to rent us kids out to the other teachers to come over to their houses with a tester a lot like the one in that picture to fix their TV's. This was the early/mid 70's...probaby '74 or '75...

  12. #9
    Supporting Member jdurand's Avatar
    Join Date
    May 2019
    Location
    Krasnodar Krai, Russian Federation
    Posts
    1,456
    Thanks
    126
    Thanked 742 Times in 416 Posts

    jdurand's Tools
    I've designed ONE device that used a "glass enclosed vacuum filled heat operated FET". It was a laser driver I designed for _____ laser company. One single triode with the grid driven by an APEX high speed high voltage op-amp. TO-3 can, cost $$$ all by itself.

    A 100MHz D to A converter drove the op-amp.

    The output from the tube followed whatever waveform was loaded into the DAC memory. 0-6000 volts.

    Getting the tubes and data sheets on them was a temporary issue. Given the end application of these devices (national research labs in the US desert and one in an island nation near China), the tubes magically appeared on my doorstep. Asking for data sheets raised all sorts of alarms of the "who are you and why do you want to know...and how do you even have one of these tubes" type. On finding out the application they gave me a heavily redacted sheet with just the info I needed visible.

    I decided to not ask what these tubes were normally used for.

    Went through the same sort of thing back in the early days of DSPs, when a box of several hundred TI DSPs was delivered to my home office the guys with sunglasses had a lot of questions.

  13. The Following User Says Thank You to jdurand For This Useful Post:

    N00b Machinist (Jun 28, 2020)

  14. #10
    Supporting Member
    Join Date
    May 2016
    Posts
    112
    Thanks
    52
    Thanked 31 Times in 21 Posts
    ...in an island nation near China....
    I believe you meant “a rogue province.” Wouldn’t want the People’s Republic to turn Sauron’s eye on homemadetools.net. Movie studios and sports leagues have caved under their Great Might. (Hail Mao!)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •