Free 173 Best Homemade Tools eBook:  
Become a founding member: 500+ tool plans, full site access, and more.

User Tag List

Results 1 to 8 of 8

Thread: WELDING TACK-UP CLIPS

  1. #1
    Supporting Member
    Join Date
    May 2020
    Posts
    54
    Thanks
    0
    Thanked 108 Times in 25 Posts

    orioncons36's Tools

    WELDING TACK-UP CLIPS

    Hello everyone! Check out this DIY welding tool/tack-up CLIPS.


    20% Off Membership

  2. The Following 15 Users Say Thank You to orioncons36 For This Useful Post:

    baja (10-20-2020), Big-Pete (10-24-2020), brianhw (10-20-2020), bruce.desertrat (10-19-2020), dubbby (10-27-2020), emu roo (10-20-2020), freddo4 (10-26-2020), high-side (10-19-2020), jackhoying (10-19-2020), Jon (10-21-2020), Karl_H (10-20-2020), lassab999 (10-26-2020), mwmkravchenko (10-19-2020), nova_robotics (10-19-2020), rdarrylb (10-20-2020)

  3. #2
    Supporting Member
    Join Date
    Sep 2018
    Posts
    180
    Thanks
    541
    Thanked 55 Times in 45 Posts

    nova_robotics's Tools
    That's slicker than snot. The pivots on the magnets are a great idea. I'm going to make a set, but with wingnuts so you can tighten the magnets in position.

  4. The Following User Says Thank You to nova_robotics For This Useful Post:

    rdarrylb (10-20-2020)

  5. #3
    Supporting Member
    Join Date
    May 2020
    Posts
    54
    Thanks
    0
    Thanked 108 Times in 25 Posts

    orioncons36's Tools
    Thank you sir. Yes, the wing nuts would be a great idea. Thank you again for your comment.

  6. #4
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,088
    Thanks
    578
    Thanked 1,412 Times in 1,267 Posts

    Thanks orioncons36! We've added your Tack Weld Clips to our Welding category,
    as well as to your builder page: orioncons36's Homemade Tools. Your receipt:


    Last edited by Jon; 10-23-2020 at 05:45 PM.

  7. #5
    Jon
    Jon is offline Jon has agreed the Seller's Terms of Service
    Administrator
    Supporting Member
    Jon's Avatar
    Join Date
    Jan 2012
    Location
    Colorado, USA
    Posts
    19,439
    Thanks
    5,720
    Thanked 26,113 Times in 7,154 Posts
    Congratulations orioncons36 - your Tack Weld Clips are the Homemade Tool of the Week!

    This was a big week with multiple nice builds, but this one wins on cleverness, simplicity, and usefulness.

    Some more good builds from this week:

    Lathe Chuck by machining 4 all
    Belt Sander From Die Grinder by Tuomas
    Wood Lathe by fox craft
    Hydraulic Press by meanwhileinthegarage
    Swivel Storage Cups by Salix84
    Revealing Stampings Method by rgsparber
    Mouse Trap by Mr.DK DIY
    Angle Grinder Stand by machining 4 all
    Electric Motor Foot Switch by HandmadeCreativeChannel
    Stove by fawabros
    Self-Contained Workshop Sink by rgsparber
    Flexible Claw by diyfixman
    AC Current Detector by mariost
    Micro Vise by universal scale models
    Welding Fume Extractor by markgyver
    Hold Down Clamps by Mazay
    Shop Vac by Sam's Workshop Diary
    Lathe Camera Mount by bouboulas
    Small Parts Cleaning Brushes by morsa


    orioncons36 - we've added your tool entry to our All Homemade Tool of the Week winners post. And, you'll now notice the wrench-on-pedestal award in the awards showcase in your postbit, visible beneath your username:



    You'll be receiving a $25 online gift card, in your choice of Amazon (US-only), PayPal, or bitcoin. Please PM me your current email address and award choice and I'll get it sent over right away.

    Nice work!

  8. #6
    Supporting Member
    Join Date
    Jun 2018
    Posts
    172
    Thanks
    71
    Thanked 411 Times in 72 Posts

    Stevohdee's Tools

    Gadget

    What a neat gadget, well done & congrats

  9. #7
    Supporting Member
    Join Date
    May 2020
    Posts
    54
    Thanks
    0
    Thanked 108 Times in 25 Posts

    orioncons36's Tools
    Thank you.

  10. #8
    Supporting Member Tuomas's Avatar
    Join Date
    Jun 2016
    Location
    Jyväskylä Finland
    Posts
    733
    Thanks
    503
    Thanked 1,522 Times in 452 Posts

    Tuomas's Tools
    Quote Originally Posted by nova_robotics View Post
    That's slicker than snot. The pivots on the magnets are a great idea. I'm going to make a set, but with wingnuts so you can tighten the magnets in position.
    I have a set of these: https://www.amazon.com/TRRAPLE-Magne...28M6P4AMESCC96

    WELDING TACK-UP CLIPS-41tfoyzverl._ac_sy400_.jpg

    Magnetig arms are rivited to body and pivoting is little tight. This actually makes them much slower to set in place and right angle. I think its better in use when hinges of the magnets are loose and pivots freely, like in the video.
    Personally i am more clamps using guy than magnets, but the video was nice and those clips works nicely too.
    Well done!


    Post your reply!
    Join 42,532 of us and get 500+ tool plans, tool eBooks, build guides, and much more.



    eBooks for Supporters

  11. The Following 2 Users Say Thank You to Tuomas For This Useful Post:

    Jon (10-29-2020), machining 4 all (10-24-2020)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •