If you have the money, buy a Mitutoyo. They maintain their position memory when turned off and the batteries last forever.
https://www.amazon.com/Mitutoyo-500-...+caliper&psc=1
Printable View
If you have the money, buy a Mitutoyo. They maintain their position memory when turned off and the batteries last forever.
https://www.amazon.com/Mitutoyo-500-...+caliper&psc=1
Marv, While in Kuwait I learned the hard way that there are knock offs to Mitutoyo, which unless you send them to a lab for inspection you can't tell them from the real thing. After that while over there I vowed never to buy another of their products except from a well known reputable dealer or to buy a used one that had documented calibrations.
That has been my experience also.
It has also been been my observation that the accuracy and repeatability of vernier and digital calipers generally exceeds the user's ability to use them correctly.
It is non-digital micrometers that I reach for when I need accuracy, which I check against a standard before any really important work. Although I am a bit anal about how I treat measuring instruments, I only look on calipers as rough and ready tools.
Yes, proper use is important. With my Mitutoyo dial calipers I can easily detect a difference of less than a thou. The people who say that (quality) calipers are only good to a few thou aren't using them correctly.
I periodically check my dial and digital calipers with my Jo blocks and they're both good to a thou if the jaws are held properly on the block.
Micrometers are wonderful tools but they're overkill for a great deal of shop measurement.
One thing I don't do is use calipers to check the diameter of something being turned on the lathe. It's almost impossible to hold calipers perpendicular to the axis and get the jaws closed squarely. For that job, a micrometer is the right tool; not only is it accurate but it's mechanically suited to the measurement being made.
About the Mitutoyo, I'll probably do that, sooner or later, but when I look at the picture of that caliper on Amazon, I find it really close to the "standard" Chinese calipers, and I am never confident to buy expensive brands who make in the same factories as noname products.
But this is unfounded, and I am ready to believe you, but that's probably why I didn't do it so far.
edit :
It's funny, just after having written that, I looked on eBay and found this one :
Mitutoyo 6'' 0-150mm/0.01mm Digital Caliper Stainless Steel Electronic Vernier | eBay
look at the description :
Mitutoyo 6 inch 0-150mm/0.01 Digital Caliper Stainless Steel Electronic Vernier Calipers
Note :
It's high quality model made in China,
but the components are the same as the original as well as the functions, please rest assured.
:lol:
I imagine that the "high quality model made in China", is one of the knock-offs mentioned earlier. A few years ago I read a thread that compared battery life on these calipers. First off, most of these calipers do not turn off, they just blank the display. The Chinese calipers had the highest current draw (even with the display blank), thus the shortest battery life. The Mitutoyo's had the lowest current draw, so they had the longest battery life. In addition, the SR type batteries that Mitutoyo uses last much longer than the LR type batteries that the cheaper calipers use. You can use a SR replacement battery in the cheaper calipers to obtain a longer battery life.
Steve
Agree. I used one of these for many years. I finally had to retire them due to the fact that the battery terminal broke and I could only repair it so well and the more I tried to fix it the worse it got until it would no longer work. But, they are great calipers and never had any other problems with them.
Funny how salesmanship fosters suspicion, "...please rest assured".
I rest best when assurance is not an issue; the point of a name brand. The phrase "Same as" is cheap, and NOT equal without genuine certifications. I can relate Aventor brand taking YT by storm, thoroughly wrung out. My old 6" TESA still hangs in there, replacement search will begin with those or Fowler Xtra-Value. I use digital calipers carefully, appreciative of "4 way measurement" feature, and selecting decimal stock by metric conversion. Most our work is metric based and while new material on hand is US and metric, drops aren't separated, so a little sketch & caliper is ideal. Just today ran some headed bushings w/ inside shoulder; from remnant tube with suitable bore to clean up. Long ago made leather 'holster' formed just like that for a revolver. Hangs by a large banker clip from belt/ waistband. Handy as a shirt pocket, 'cept won't fall out!
While changing out of work garb in the locker room today, had to laugh out loud, real loud.
"Rest Assured" is printed on the package of toilet seat covers...