21 Drawer Cabinet

Hello again.

Have no idea in which category this should go, probably tools organizers.

Last summer I made 21 drawers cabinet which fits inside my lathe stand.

When I bought my lathe CQ6128 x 660 (big brother of G0602) it came together
with lathe stand. That metal stand was complete disaster. So, immediately
afterwards I decided to fabricate new lathe stand. Checked numerous web pages
in order to find suitable design and found really great design for lathe bench at
Heavy duty work bench with retractable wheels

Then I searched for good wheels and found some good "Blickle" wheels -
German made, only 50 mm high and able to stand 100 kilograms. Bought 4 pieces
and once they arrived, started with stand fabrication. Don't have any drawings
of that stand, but it can be seen on the pictures.
Stand dimensions are 1400 mm x 600 mm x 850 mm high made of 40 x 40 x 4 mm square tube.
That design with retractable wheels is good if you need to move lathe from one place to
another and so far I moved it twice. Last time even with drawers cabinet inside.

Anyways this lathe stand is not subject of this post. Just to show what mess was
under the lathe which made me desperate to do something about tools storage.
Space inside the stand was big enough to put 1300 x 600 x 650 mm high cabinet.

Took me couple of months to complete my drawings with every single detail how
to fabricate 21 drawers cabinet where I keep most of my precious tools now.

Made numerous drawings and finaly settled on 21 drawers and melamine board.
There were also combinations with plywood (too expensive) and 16, 18, 24, 28
drawers. Also with bearing guiders. So, in order to save space and money,
final decision was 21 drawers, hardwood 12 x 12 mm guiders and melamine board,
18 mm thickness for all except bottom parts of drawers which is made of 10 mm melamine.
Even downloaded freeware program "MaxCut" for board cutting optimization and finally
ordered melamine material to be cut and edged according to my specifications.

Here are couple of pictures and 2 drawings.

Hope that this will help someone to build good tools storage space.

LMMasterMariner

Quite a masterful build LMMasterMariner! Lots of storage room for anything one could imagine. Those casters look great to me with the dual bearings and with your leveling foot system you shouldn't get any flat spots from resting on the Polyurethane. The only thing I might have done different (only because I always over pack my storage) is used 1/2 or 5/8 (13/16mm) ply for the bottoms of the big drawers. Over all a beautiful build and Well Done! Thanks for sharing it.

LM, very nicely done! I worry tho because I always seem to pull drawers too far, do you have "stops" for them?
I would love a setup like that!

Hello JD62, I've been thinking about the stops, but didn't make them. So, I must be very careful when pulling drawers out. Also I keep drawer with one hand while drawer is open.

Nice build. I need to make a set for my lathe table. I don't have any drawer stops in my workbench drawers that I have already built. I use a "safety" drawer. That is I always open the drawer below the one I am opening to full depth to about half depth. Makes a nice shelf for the upper drawer to sit on. It has saved me the "pickup tools mess" many times and it is still easy to remove the drawer completely when necessary. Two sets of the drawer units are full of screws, nuts and bolts so it is quite important not to dump them.

Your design is just what my lathe table needs!

Cheers, JR

JR, thanks for advice. I actually don't need it as long as I open drawers up to 3/4 of their length (approx. 40 cm) even some of them are overloaded. There are guiders above and below drawers and total clearance is 2 mm.

Quote:

---

Originally Posted by LMMasterMariner

JR, thanks for advice. I actually don't need it as long as I open drawers up to 3/4 of their length (approx. 40 cm) even some of them are overloaded. There are guiders above and below drawers and total clearance is 2 mm.

---

Yes indeed! That was one of the design items I really liked about your unit. When I made mine I used shop made maple drawer guides that run in a slot in each side of the drawer and of course some clearance between the drawer and rail needs to be included. I have about 1/16" clearance from the guide to the slot. No secondary support is needed until like you say "the drawer is pulled out past 3/4 of their length". My drawers are 30" long and about 16 of them are full of screws. To get to the ones in the back I frequently need the additional support.

Cheers, JR

UPDATE
======

This 21 Drawers Tools Storage Cabinet has been completed long time ago, actually at the time when I posted it.
Here are couple of fresh pictures just to show what it looks now.
Please move this thread from 'tools in progress' forum to 'homemadetools' forum.
Many thanks in advance / Best regards
LMMasterMariner

Just copied all the pics...Getting closer to the build.
Thanks again, JR

Just what I needed for my lathe bench. What is the hydraulic jack for?

Ralph

Ralph,

Check my reply to your thread 'Rolling Mill'.
Use of hydraulic jack can be found at https://www.garagejournal.com/forum/...d.php?t=222930
Cheers,
LMMasterMariner

This is the only reply that I see.

I could see how the jack lowered the casters but could not see how they were retracted untill I saw the Norlift site and finally see the springs for retraction.

Ralph

Ralph,

Here is my reply to your thread "Rolling Mill". Can be found at page 2, just before you wrote that your mill fell over backwards.....

Quote:
Ralph, I fully understand you as I have the same problem. Very small workshop (3 x 2 meters) and I also must be able to move my lathe and mill around in order to put them in their final positions. I made it little bit differently and I used idea at The Heavy Bench - The Garage Journal Board. Have the same bars with casters and same hydraulic jacks for both.
2 pictures attached.
Regards
LMMM
Unquote

Best regards
LMMasterMariner

oh, I had forgot about that incident!! Yeah the heavy benches, machines need to move around especially in a small shop.

I am "thinking" about taking my Mill off it's stand and mounting it to a heavy bench, which again would be mounted on casters.

Now I need some more detailed pictures of exactly how your retraction springs are fitted.

Ralph

I didn't put retraction springs at all as I didn't need them. When the bench is on the casters just move it around the workshop and once bench is in it's final position, just open release valve at bottle jack and bars with casters will lift up. Actually complete bench is coming down and then it stands on the feet. As I have the same bars, casters and hydraulic jacks for both; lathe bench and milling/drilling machine, I keep bars with casters on one which was moved last. In my case at lathe bench.

Cheers,
LMMasterMariner

Oh interesting, the Norlift heavy bench has springs.

Ralph

<!-- BEGIN /var/www/html/homemadetools/protected/modules/zeus/views/tool/postUpdate.php -->
Thanks LMMasterMariner! We've added your Tool Cabinet to our Storage and Organization category,
as well as to your builder page: LMMasterMariner's Homemade Tools. Your receipt:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="http://www.homemadetools.net/homemade-tool-cabinet-4"> <img src="/uploads/210188/homemade-tool-cabinet-4.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="http://www.homemadetools.net/homemade-tool-cabinet-4">Tool Cabinet</a> <span> by <a href="http://www.homemadetools.net/builder/LMMasterMariner">LMMasterMariner</a></span> </div> <div class="tags">tags: <a href='http://www.homemadetools.net/tag/cabinet'>cabinet</a>, <a href='http://www.homemadetools.net/tag/tool'>tool</a> </div> </div> </div> </div>
<!-- END /var/www/html/homemadetools/protected/modules/zeus/views/tool/postUpdate.php -->

OK thats a drawer full of tools as I see it....nice job looks perfect..:O)


P.S. send it over here when you get tired of them...:rofl:

Hi Cap,
I am afraid I will never get tired of these tools and my workshop.
Cheers,
LMMasterMariner

I was thinking you would say that . He He :thumbsup: