Ball Turner.

A couple of ball turners.

Number One:

I wanted a tool I could just mount in the tool post rather than one that sits on top of the cross slide. I also wanted one that sat behind the work so I could get a better view, although it can be used at front as well, you just have to remove the handle, change the cutting head to the other end of the base and re attach the handle.

Once mounted on the tool post, the compound is set parallel to the bed and to the rear of the cross slide. After measuring the length of the cutting bit to give the right diameter ball, wind the cross slide forward until the cutting tip is central to the work and lock off the cross slide - this in effect sets the cutting tool height

Using the carriage bring the tool up to touch the beginning of the work and lock off then wind the compound out a little and start cutting, advancing the compound with each pass until you reach the front off the work again, hey presto – Balls!

I also tried it on a piece of acrylic to make a convex lens, that also worked well. I set the diameter limit at 50mm, I can’t imagine wanting bigger balls than that!

In the design stage I realized it did have one peculiarity; but, I decided I could live with that peculiarity if the trade off was a tool that was so simple and easy to use. That peculiarity: it only cuts round balls because the height is set.



Number Two:

Buoyed on by the success of the welded together ball turner I constructed, I made a second from solid stock. This one has a ball limit of 60mm and is adjusted via the cutting head rather than by the cutting tool thus keeping the tool overhang to a minimum. This one will cut oval as well as round balls.

The base was made from a piece of 50x25 and milled down on the lathe as was the pivot/cutting head support. The hand wheel was made from a piece of 6mm plate, the cutting head from an off cut from the 50x25 and the cutting head slide from a piece of 16mm round. No welding on this one,

It works well, the hand wheel making it easier to use than a lever. The wheel could be larger but I was limited by the size stock I had on hand.

Used in much the same way as the first, if your preference is for ovals simply move the tool up or down in the tool post

Attachment 5502Attachment 5503Attachment 5504Attachment 5505Attachment 5506Attachment 5507

Thanks th62! We've added your Tool Post Ball Turner to our Lathe Accessories category, as well as to your builder page: th62's Homemade Tools. Your receipt:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="http://www.homemadetools.net/tool-post-ball-turner"><img src="http://www.homemadetools.net/uploads/131778/tool-post-ball-turner.jpeg" /></a></div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="http://www.homemadetools.net/tool-post-ball-turner">Tool Post Ball Turner</a> <span> by <a href="/builder/th62">th62</a></span> </div> <div class="tags">tags: <a href="http://www.homemadetools.net/tag/ball-turning">ball turning</a></div> </div> </div> </div>

Thanks th62! We've added your Ball Turner to our Machining category, as well as to your builder page: th62's Homemade Tools. Your receipt:

<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="http://www.homemadetools.net/ball-turner-17"><img src="http://www.homemadetools.net/uploads/131782/ball-turner-17.jpeg" /></a></div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="http://www.homemadetools.net/ball-turner-17">Ball Turner</a> <span> by <a href="/builder/th62">th62</a></span> </div> <div class="tags">tags: <a href="http://www.homemadetools.net/tag/ball-turning">ball turning</a></div> </div> </div> </div>

th62,

I like the solid stock design and looks easy to use with the wheel for rotations. How deep of a cut per pass do you use for cutting a radius in cold rolled steel bars?

Thanks for sharing this,
Paul Jones

I have no idea actually, I tend to just wind it back and forward with light cuts until I get close to size then make the final cuts in a more slow and controlled way.

I have been thinking how useful a ball turner would be recently, and this is a great one! Thanks for posting it up. Doesnt look like it would be too hard to make some on a larger scale also.

th62;
Would love to be able to try your lil creation out and make one for myself, with permissions of course, are there perhaps any technical drawing or even scribbles that would give dimensions etc? materials used and such?

Quote:

---

Originally Posted by Charron63

th62;
Would love to be able to try your lil creation out and make one for myself, with permissions of course, are there perhaps any technical drawing or even scribbles that would give dimensions etc? materials used and such?

---

Sorry mate, I do everything off the top of my head, never work from drawings. Sizing would depend on your lathe and your work envelope.

th62
Nice work, always nice to see someone else likes ball turning. How do you cut the chuck side of the ball? I have two ball turners and the one I like the best came from an old hand that past years ago. Steve Bediar what a special person to go too soon. You can check out his web site it is full of great upgrade and toys for the shop. The ball turner is here: Steve Bedair's 9x20 Lathe Site

Nelson

A bit late, but yes, I'm familiar with Bedair's site. My first lathe was a 9x20, I graduated to an AL-300, then back to a 9x20. They are a great little lathe.