Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: Drill press slop

  1. #1
    bricolage's Avatar
    Join Date
    Sep 2017
    Posts
    8
    Thanks
    2
    Thanked 8 Times in 4 Posts

    Drill press slop

    I make 1/6th scale miniature chairs, so you can imagine that drilling small holes in the edge of thin wood can be a problem. When drilling a 1/16" hole, for example, I use a center drill initially to avoid the thin drill bit following the grain. However I notice that the center bit drills off center every now and then and found that there is slop in the quill or somewhere. I have a Ryobi and an old VIP Proline bench top drill press and they both have the same problem. I would hate to have to go buy a more expensive drill press to overcome this problem. Does anyone know of a way to tighten up said quill.

    http://www.miniaturechairmaker.com

    186 More Best Homemade Tools eBook

  2. The Following User Says Thank You to bricolage For This Useful Post:

    Seedtick (Mar 13, 2018)

  3. #2
    Supporting Member olderdan's Avatar
    Join Date
    Jun 2016
    Posts
    781
    Thanks
    1,456
    Thanked 1,531 Times in 463 Posts

    olderdan's Tools
    Hi bricolage
    I had a similar problem with my inherited Record bench drill (a lot of budget drills have this defect). I have drilled and tapped the head for a brass padded bolt to put drag on the quill to take up the play when needed, it also serves as a lock. It is a bit of a bodge fix but it works and could be refined to a spring loaded device, but at least it makes a worn machine more usable.
    Drill press slop-drill.jpg
    I hope this helps you in making those beautiful miniature chairs.

    2000 Tool Plans

  4. The Following 4 Users Say Thank You to olderdan For This Useful Post:

    bricolage (Mar 13, 2018), Paul Jones (Mar 21, 2018), PJs (Mar 14, 2018), suther51 (Mar 13, 2018)

  5. #3
    Supporting Member
    Join Date
    Aug 2016
    Posts
    635
    Thanks
    1
    Thanked 187 Times in 166 Posts

    wizard69's Tools
    Some drill presses have a extended casting at the front long enough to support a clamp bolt. You would need to disassemble the quill assembly, slit the casting and drill and tap for a bolt. This would give you some take up but probably not enough if you need more than a few thousands (you wouldn't want to stress the cast too much).

    Another option would be to have the outside of the quill hard chromed and then hand fit it to the bore. This of course depends upon having a near by plating lab that knows how to hard chrome machine tool parts. In any event you may be able to get a decent build up.

    Do be aware though that some drill presses are inherently bad design wise. The support for the quill is often marginal relying upon the drive pinion to keep it in place. There simply may not be enough meat there for proper quill support. Sadly you have to take the drill apart in most cases to see how much support is there for the quill. As for the spindle don't dismiss some slop in the spindle bearings contributing to your issue. Especially at the low end the cheapest bearings possible are often used in these drill presses.

    In any event unless you have a well equipped machine shop it might take more work that the drill press is ultimately worth to fix it up. One example of a guy doign an elaborate rebuild of a cheap Chinese drill press is on Youtube. Basically he made a entirely new quill out of steel that was precisely fitted to the casting bore

  6. The Following 2 Users Say Thank You to wizard69 For This Useful Post:

    bricolage (Mar 13, 2018), Paul Jones (Mar 21, 2018)

  7. #4
    Supporting Member suther51's Avatar
    Join Date
    Jul 2016
    Posts
    380
    Thanks
    210
    Thanked 150 Times in 115 Posts
    My grizzly drill press has this problem, tight with the quill all the way up but sloppy extended. There is a set screw in the side, but when the slop is taken out extended, quill will not retract. Set screw rides in a v shaped slot in the quill. May at some point try to touch up the slot. Or add the brass tipped set screw at another spot on the quill as just suggested by Olderdan.
    Eric

  8. The Following User Says Thank You to suther51 For This Useful Post:

    Paul Jones (Mar 21, 2018)

  9. #5
    bricolage's Avatar
    Join Date
    Sep 2017
    Posts
    8
    Thanks
    2
    Thanked 8 Times in 4 Posts
    Thanks to those of you that replied with suggestions. Neither machine is worth spending too much time and money on. When I have a spare moment I will try Olderdan's idea. I got through that particular process with a 30% wastage, but I had expected a fair amount anyway, so now I can press on.

  10. The Following 2 Users Say Thank You to bricolage For This Useful Post:

    Paul Jones (Mar 21, 2018), PJs (Mar 14, 2018)

  11. #6
    Supporting Member metric_taper's Avatar
    Join Date
    Mar 2017
    Location
    Marion, Iowa
    Posts
    585
    Thanks
    227
    Thanked 257 Times in 153 Posts

    metric_taper's Tools
    Bricolage, I know your not looking at replacing your existing DP, but if you were, Harbor Freight has a 20 inch DP that has a slit cast iron head stock, with 3 adjusting bolts to take the slop out of the quill movement. Price is $580.
    Drill press slop-drill-press.jpg
    Cap screws 66 and 67 in the above snap shot from the owners manual from their web site shows this adjustment.
    I've owned this model for more then 25 years. I've also replaced the junk drill chucks with keyless that have less then .0015 runout. It has a MT3 taper. The only issue I have is the slight bit of slop in the quill rack/pinion, but all drill presses I've used have this problem.
    Last edited by metric_taper; Mar 13, 2018 at 09:04 PM.

  12. The Following User Says Thank You to metric_taper For This Useful Post:

    Paul Jones (Mar 21, 2018)

  13. #7
    Supporting Member pfredX1's Avatar
    Join Date
    Sep 2016
    Location
    Delaware
    Posts
    162
    Thanks
    6
    Thanked 121 Times in 62 Posts

    pfredX1's Tools
    I don't think slop is what's causing your problem. You're probably not spinning fast enough. Your drill bits may not be as sharp as they need to be either. Drilling wood with a 1/16th inch diameter drill bit you should be running about 10,000 RPM. That nets you 163 surface feet per minute. Which is well within the capability of HSS drilling wood. Then you'll be cutting fibers instead of tracking along the grain.

    I can only encourage you to try to sharpen your drill bits too. That is something you just have to work at. When you get good at it it's nice to always have very sharp bits. New bits are not always all that sharp either. What I'm saying is when you get good you can do better. But skill like that is not something you can expect to achieve 1, 2, 3. It takes a bit of effort. Most folks won't even bother trying to sharpen small diameter twist drills. Me, I'm not most folks. You seem to be doing what most folks won't try to do yourself. As far as tricks go magnification is essential, along with a well trued and dressed grinding wheel. Past that it's motor skills. I dare say there's a bit of mind over matter going on in there as well. Visualization helps.

  14. The Following User Says Thank You to pfredX1 For This Useful Post:

    Paul Jones (Mar 21, 2018)

  15. #8

    Join Date
    Dec 2016
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Lightbulb

    Quote Originally Posted by bricolage View Post
    I make 1/6th scale miniature chairs, so you can imagine that drilling small holes in the edge of thin wood can be a problem. When drilling a 1/16" hole, for example, I use a center drill initially to avoid the thin drill bit following the grain. However I notice that the center bit drills off center every now and then and found that there is slop in the quill or somewhere. I have a Ryobi and an old VIP Proline bench top drill press and they both have the same problem. I would hate to have to go buy a more expensive drill press to overcome this problem. Does anyone know of a way to tighten up said quill.

    http://www.miniaturechairmaker.com
    I saw a potential fix with a guy making a milling machine from an old bdp (a youtube clip he even shows where je bought the various bits incl the bearing on ebay)). In short he removed the quil and replaced the bearing inside the quill with a longer double row version, this did require macining the bearing groove about 6mm longer in the quill but keeping the same id. I too have one with this problem and will try this when time permits.

  16. #9
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 442 Times in 180 Posts

    old_toolmaker's Tools
    Suther51,

    Have you considered placing a strong Vlier spring plunger or ball plunger in place of the set screw?
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

  17. The Following 2 Users Say Thank You to old_toolmaker For This Useful Post:

    Paul Jones (Mar 21, 2018), suther51 (Mar 14, 2018)

  18. #10
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 442 Times in 180 Posts

    old_toolmaker's Tools
    bricoage,

    I have a vintage Toro drill press with issues similar to your drill press that I would like to solve. It has the split casting with cross bolt for snugging and locking the quill which does not work well as the casting hole is larger than the quill by several thousandths. I will be following this thread with interest in hopes of finding a better way to fix this.
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

  19. The Following User Says Thank You to old_toolmaker For This Useful Post:

    Paul Jones (Mar 21, 2018)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •