https://youtu.be/zcPXsSwEHTk
Link to tool: https://amzn.to/35tnHJR
Printable View
https://youtu.be/zcPXsSwEHTk
Link to tool: https://amzn.to/35tnHJR
I like the modification. I do most of my knurling in stainless steel rods using three passes with increasing knurling tool pressure per pass. I usually start with one pass toward the headstock, stop the rotation and reverse the carriage to go back towards the tailstock, and then a final pass towards the headstock with slightly more knurling pressure without disengaging to carriage feed. I use lubricating oil and not cutting oil. If I discover on the final pass the knurl depth is not deep as required it is easy to reengage the knurl pattern by slowly tightening the scissor-type knurling tool on the knurl pattern and running another pass. It is easier to take a little longer when during the knurling than trying to do it in one pass.
There are different opinions on using the correct diameter of the bar stock before starting the knurling operation but I prefer reducing the bar stock for an optimum knurl pattern. I used to use a formula for the optimum diameter but as they say there is an app on your phone for this. I use the free phone app "Knurling Calculator". It only works for Imperial dimensions but very easy to use. The drop-down menu is for 12 to 80 TPI knurls. Next the blank diameter is specified in inches and calculator provides the starting diameter. I usually add 0.002" to the final calculated diameter. I achieve perfect and sharp knurls every time.
Cool info, I have best luck with one heavy pass but then again I don;t worry about diameter. With a close to correct diameter I'm sure you method works great. I've never tried to knurl stainless.Quote:
Originally Posted by winkys workshop
Man they have apps for everything! I'll check it out. Thanks
For the folks like me who won't own one of those smart phone timesuckers*, there's a program to compute perfect knurling diameter on my page as well as one from Little Machine Shop on the interweb...Quote:
Originally Posted by Paul Jones
https://littlemachineshop.com/reference/knurler.php
The basic mathematics is simple...
Compute the circular pitch of the knurl wheel... p = wheel diameter / number of teeth
Compute the integer number of p's in the stock of diameter D... N = int[ pi*D/p ] where the "int" operator denotes truncation to an integer
Then the desired knurling diameter is given by N*p / pi.
---
* Yeah, that's right, I'm retired and gloat on the fact that I can get along just fine without one.
For larger diameters many folks, if they initially get a doubled knurl, just keep pushing the tool deeper until it reaches a diameter where correct diamonds form. This leaves a botched section at the start of the knurl which demands removal.
For smaller diameters this bullish approach doesn't work as well, especially if a push knurler is in use.
I've had a number of bad knurls forming without using the correct diameter; I've never had that happen when using the computed correct diameter.
Marv,
Very good reply. The tried and true knurling formula is a the way to go for imperial and metric knurls but using a "canned" app is so much easier.
I have recovered the "botched section at the start or end of the knurl" by practicing the method to systematically reengaging the knurling tool until the knurl rollers start to roll, sync and then increase the knurl tool pressure for yet another knurl pass. I have saved a lot of stock trying this technique.
Paul
I don't knurl very often but it certainly is a process that requires practice.Quote:
Originally Posted by Paul Jones
<!-- BEGIN /var/www/html/homemadetools/protected/modules/zeus/views/tool/postUpdate.php -->
Thanks winkys workshop! We've added your Knurling Tool Lathe Mount to our Metalworking category,
as well as to your builder page: winkys workshop's Homemade Tools. Your receipt:
<div id="blocks"> <div class="block b1 pngfix"> <div class="bimg"> <div> <a href="https://www.homemadetools.net/homemade-knurling-tool-lathe-mount"> <img src="/uploads/241687/homemade-knurling-tool-lathe-mount.jpeg"/> </a> </div> </div> <div class="head pngfix"></div> <div class="left pngfix"></div> <div class="right pngfix"></div> <div class="blockover b1 pngfix"> <div class="title"> <a href="https://www.homemadetools.net/homemade-knurling-tool-lathe-mount">Knurling Tool Lathe Mount</a> <span> by <a href="https://www.homemadetools.net/builder/winkys+workshop">winkys workshop</a></span> </div> <div class="tags">tags: <a href='https://www.homemadetools.net/tag/lathe'>lathe</a>, <a href='https://www.homemadetools.net/tag/knurling'>knurling</a>, <a href='https://www.homemadetools.net/tag/mount'>mount</a> </div> </div> </div> </div>
<!-- END /var/www/html/homemadetools/protected/modules/zeus/views/tool/postUpdate.php -->