Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14

Thread: Lever dolly

  1. #1
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools

    Lever dolly

    My mill has been stuck in the entrance of my workshop. Until now I haven't been able to move it into its permanent place. So, I needed a lever dolly (like a pry bar on wheels). Here's my take on building one from scratch.

    Since I couldn't see any other videos about making one, I decided to make a video about designing and making it.

    Some of the materials are new, but I was able to make about half of this project from recycled steel.

    Axle is made from 32mm steel round bar
    2 x 6305-2RS bearings
    1.5m of 50x25x3mm rectangular steel tube for the handle.
    300mm of 50x12.5mm hot rolled flat bar for toe and heel

    See the build here:



    Thanks,
    Craig

    186 More Best Homemade Tools eBook

  2. The Following 19 Users Say Thank You to craig9 For This Useful Post:

    Altair (Jul 15, 2019), baja (Jul 16, 2019), Beserkleyboy (Jul 15, 2019), Christofix (Jul 16, 2019), Eaglewood (Jul 15, 2019), EnginePaul (Jul 16, 2019), enginepaul1 (Sep 1, 2021), flyfr8rs (Aug 26, 2021), high-side (Jul 21, 2019), jackhoying (Jul 15, 2019), Jon (Jul 15, 2019), kboy0076 (Feb 10, 2023), machewa (Jul 22, 2019), mwmkravchenko (Jul 15, 2019), nova_robotics (Aug 26, 2021), Ralphxyz (Sep 27, 2023), rlm98253 (Jul 15, 2019), Sleykin (Jul 16, 2019), Toolmaker51 (Jun 14, 2022)

  3. #2
    Content Editor
    Supporting Member
    Altair's Avatar
    Join Date
    Aug 2013
    Posts
    11,722
    Thanks
    1,353
    Thanked 29,236 Times in 9,716 Posts


    Thanks craig9! We've added your Lever Dolly to our Miscellaneous category,
    as well as to your builder page: craig9's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. #3
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools

    Smile

    Quote Originally Posted by Altair View Post
    Thanks craig9! We've added your Lever Dolly to our Miscellaneous category,
    as well as to your builder page...
    Thanks for the addition, Altair!

    Cheers,
    Craig

  5. #4
    Supporting Member Beserkleyboy's Avatar
    Join Date
    Aug 2014
    Location
    Sunny South Coast NSW, Australia
    Posts
    366
    Thanks
    473
    Thanked 226 Times in 132 Posts

    Beserkleyboy's Tools
    Great work Craig!
    Reminds be of moving my (ex) Jonsered 20" thicknesser (800kg) around with a crude lever and the 'Egyptian' pipe method...necessity is the mother of invention... Cheers
    Jim in the now equally cold South Coast NSW..

  6. #5
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools
    Hey Jim. Yes - levers and wheels and rollers can get a lot done. I know engineers mastered the "simple machines" hundreds (or thousands) of years ago, but to me they are still exciting and fascinating.

    Being able to trade distance for force allows us to do nearly anything.

    Stay warm!

    Cheers,
    Craig

  7. The Following User Says Thank You to craig9 For This Useful Post:

    Beserkleyboy (Jul 15, 2019)

  8. #6
    Supporting Member Saltfever's Avatar
    Join Date
    Apr 2012
    Location
    NorCal
    Posts
    348
    Thanks
    389
    Thanked 123 Times in 84 Posts

    Saltfever's Tools
    This exact same tool is available from Northern Tool for $66 - $79 (depending on sale).
    Attached Thumbnails Attached Thumbnails Lever dolly-pry-bar.jpeg  

  9. The Following User Says Thank You to Saltfever For This Useful Post:

    craig9 (Jul 15, 2019)

  10. #7
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools
    Hi Saltfever, yes very similar - but not available in Tasmania that I could find.

    I had found that image and used it (and others) as inspiration for my build.

    I deviated from it in the following ways: rectangular tubing replaces the bumper and the round tubing (stronger lever arm and smaller parts count), and simpler to make the end fit around the axle. The toe and heel are also made thicker. 1/2" thick compared to what looks like 3/8". Also, I don't reduce down the toe quite as much. Mine finishes up at just under under 1/4" at the tip, less of a knife edge.

    Cheers,
    Craig

  11. #8
    Supporting Member Saltfever's Avatar
    Join Date
    Apr 2012
    Location
    NorCal
    Posts
    348
    Thanks
    389
    Thanked 123 Times in 84 Posts

    Saltfever's Tools
    I find the knife edge is very useful for equipment that is flush to the floor. Usually you can grip just enough and lever up the machine to put a small shim under it to create a better gap and gain a better grip. I plan to attach 2 wheels in back of some heavy equipment and fabricate some kind of attachment on to the lever-bar so I can raise the equipment onto the back wheels and steer equipment around the shop. The product is made in China and most likely importers all over the world have it in their catalog somewhere. Great video quality . . . nice job.

  12. #9
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools
    One of the difficulties is finding the right search term for this kind of device. There are a lot of similar tools that exist in roughly overlapping categories: burke bars, lever dollies, pry bars, some have wheels and some don't, and some have a wooden handle and some don't. I settled on naming this one a lever dolly, because it's very similar to the one you posted, and in general, because when I did a google image search of "lever dolly", the results were most like what I wanted. I couldn't find anything all steel with wheels sold locally to me though, and the one I've made weighs at least 10kg or 20lb+, so I didn't want to pay shipping on that weight either. (Plus I try to be frugal and I like making things.)

    Thanks for the comments on the video quality - much appreciated.

    Cheers,
    Craig

    Edit: Sorry didn't mean to ignore the good point you made about the knife edge. My mill has three lifting areas where I can get a thicker piece to fit, gaps that are possibly 3/8" or 10mm high. From there I can get it up on blocks or rollers and lift from anywhere. If I change machines though in future and need the thinner edge, it's possible to remove the bearings, put the foot up on the mill table and thin it down if needed. If I go too far it's easy to put metal back on too. Metal is good like that Cheers.
    Last edited by craig9; Jul 15, 2019 at 07:44 PM.

  13. #10

    Join Date
    Dec 2020
    Posts
    4
    Thanks
    2
    Thanked 0 Times in 0 Posts

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •