Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 5 of 5

Thread: Mini drill

  1. #1
    Supporting Member Workshopshed's Avatar
    Join Date
    Mar 2013
    Location
    Ayrshire, UK
    Posts
    210
    Thanks
    129
    Thanked 147 Times in 90 Posts

    Workshopshed's Tools

    Mini drill

    I've an old mini-craft drill and it's loosing power on me. I was wondering if I could dissect it and use the bits with a new motor to make a new one.
    Has anyone tried anything like that?

    186 More Best Homemade Tools eBook
    Andy from Workshopshed
    "Making and repairing things in a shed at the bottom of the garden"
    workshopshed.com

  2. #2
    Supporting Member C-Bag's Avatar
    Join Date
    Aug 2015
    Location
    California, central coast
    Posts
    720
    Thanks
    689
    Thanked 876 Times in 471 Posts

    C-Bag's Tools
    I'm sorry I don't have any good info for you Andy, but I am so curious.....what's a "mini-craft drill"? Is that what we call over here a Dremel tool? And are you sure it doesn't just need a new set of bearings? Or brushes? I've brought back many a hand held grinder and a couple of hand held drills that way.

    The next deeper repair would be to rewind the armature and at that point I usually decide I've passed some kind of balance between amount of time invested to return on said investment. I do get really attached to my tools I've had for a long time. I have all of my first Proto mechanic starter set from 1975, except the top box and a couple of pieces. They truly don't make them like that anymore and it might be true with your drill, dunno.

    2000 Tool Plans

  3. #3
    Supporting Member Workshopshed's Avatar
    Join Date
    Mar 2013
    Location
    Ayrshire, UK
    Posts
    210
    Thanks
    129
    Thanked 147 Times in 90 Posts

    Workshopshed's Tools
    Yes, it's just like a Dremel.

    Mini drill-drill.jpg

    In the process of looking for a picture I found these
    My Minicraft drill has died
    HydraRaptor: End of play

    Also looking on ebay there do seem to be some quite economical replacements for me. It also gave me the idea of seeing if I could make an adapter for my angle grinder so it could take some of the tools from the mini drill.
    Andy from Workshopshed
    "Making and repairing things in a shed at the bottom of the garden"
    workshopshed.com

  4. #4
    Supporting Member C-Bag's Avatar
    Join Date
    Aug 2015
    Location
    California, central coast
    Posts
    720
    Thanks
    689
    Thanked 876 Times in 471 Posts

    C-Bag's Tools
    Wow, that end play link shows that's not much there to scavenge. It does look like it would be pretty straight forward to just replace the motor though.

    My problem with Dremel's is they just don't have enough uumph for me and everything I try to do with it loads it down so much I get scared it's going to burn up on me. My go to at work where there was a huge compressor was a small air die grinder. But you need a good sized compressor for the beast. Through HF they are only like $14, but you need a $500++ compressor to run it for any time.

    HF also has a long shaft electric die grinder that is awesome. I have two them, but they are much more bulky but they go at 22,000 rpm and I just can't load them down they have so much power.

    Have you though of one of those cable drive units that are powered by a bench grinder? I don't know if the limiting factor is cable or the fact it only rotates at 3400rpm, or the cable is too short.

  5. #5
    Supporting Member Workshopshed's Avatar
    Join Date
    Mar 2013
    Location
    Ayrshire, UK
    Posts
    210
    Thanks
    129
    Thanked 147 Times in 90 Posts

    Workshopshed's Tools
    I stripped the drill down last night and cleaned out some of the metal filings. I tweaked the bearing, fan and shaft positions until it ran a more freely, care was needed so that the spindle lock would still engage. After about 45 minutes of tuning it was running smoothly again. The brushes looked ok but the commutator looked a bit dirty, not quite sure how to clean that as the motor is mostly encased with a couple of air vents.

    Seems to have done the trick for now. Sorry no photos as I was not actually planning to do that job yesterday.



    186 More Best Homemade Tools eBook
    Andy from Workshopshed
    "Making and repairing things in a shed at the bottom of the garden"
    workshopshed.com

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •