Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 9 of 9

Thread: Vise holddowns

  1. #1
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools

    Lightbulb Vise holddowns

    Hi folks,

    I needed a way to hold my precision grinding vise down on the mill table, so I carved up some recycled cold rolled steel, and made some chunky and solid hold downs. The design allows for maximum support, minimum metal chip collection, and you can also use the holddowns with 2 instead of three bolts, allowing the vise to be placed fore and aft on the table.



    This video was also made as an entry into the #tmc2020 tool making competition held by Emma at Emma's Spareroom Machineshop. If you search youtube for #tmc2020 , you will find a bunch of other tools made on video, that you might find interesting.

    Cheers,
    Craig

    186 More Best Homemade Tools eBook

  2. The Following 6 Users Say Thank You to craig9 For This Useful Post:

    Carnel (Jul 22, 2020), Crusty (Jul 21, 2020), high-side (Jul 27, 2020), Home-PC (Jul 24, 2020), jjr2001 (Jul 21, 2020), Jon (Jul 21, 2020)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks craig9! We've added your Vise Hold Down to our Vises category,
    as well as to your builder page: craig9's Homemade Tools. Your receipt:




    2000 Tool Plans

  4. #3
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools
    Very nice Craig9. I really like your hold downs for a machinist vise. I too use machinist vises on my small milling machine and will
    most likely make a pair of your designed hold downs for my vise.

    Cheers, JR
    Back to the shop.

  5. #4
    Supporting Member Crusty's Avatar
    Join Date
    May 2019
    Location
    Dry Gulch, Tx
    Posts
    749
    Thanks
    220
    Thanked 845 Times in 324 Posts

    Crusty's Tools
    Hmmm. That gives me an idea for a way to clamp down my little rotary table in horizontal mode.
    If you can't make it precise make it adjustable.

  6. #5
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools
    Quote Originally Posted by jjr2001 View Post
    Very nice Craig9. I really like your hold downs for a machinist vise. I too use machinist vises on my small milling machine and will
    most likely make a pair of your designed hold downs for my vise.

    Cheers, JR
    Hey JR - that's great. Good luck with the build. I am sure they will work great for you.

    Cheers,
    Craig

  7. #6
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools
    Quote Originally Posted by Crusty View Post
    Hmmm. That gives me an idea for a way to clamp down my little rotary table in horizontal mode.
    Hi Crusty - it would be great to see what you come up with.

    Cheers,
    Craig

  8. #7
    Supporting Member Crusty's Avatar
    Join Date
    May 2019
    Location
    Dry Gulch, Tx
    Posts
    749
    Thanks
    220
    Thanked 845 Times in 324 Posts

    Crusty's Tools
    It will be much like your clamps but without the screw in the center because the chuck on the rotary table won't allow access for tightening in that location. The lip on the clamp inserts into a slot in the rotary head and the block is sized to pull it down to the table (or maybe I'll use shims underneath to get it pulled down just right).

    I made a low profile milling vise that's much like it so it shouldn't be too difficult.

    Vise holddowns-low-profile-milling-vise.jpg
    Last edited by Crusty; Jul 28, 2020 at 12:02 PM.
    If you can't make it precise make it adjustable.

  9. #8
    Supporting Member craig9's Avatar
    Join Date
    Jul 2019
    Location
    Hobart, Tasmania
    Posts
    56
    Thanks
    22
    Thanked 99 Times in 28 Posts

    craig9's Tools
    Quote Originally Posted by Crusty View Post
    It will be much like your clamps but without the screw in the center because the chuck on the rotary table won't allow access for tightening in that location. The lip on the clamp inserts into a slot in the rotary head and the block is sized to pull it down to the table (or maybe I'll use shims underneath to get it pulled down just right).

    I made a low profile milling vise that's much like it so it shouldn't be too difficult.

    Click image for larger version. 

Name:	Low Profile Milling Vise.jpg 
Views:	148 
Size:	46.4 KB 
ID:	35946
    That low profile vise is great. What have you used for sliding pins and bushings - any particular material?

    The plan for the rotab clamp sounds good. I'd definitely take the extra few mins and mill a small step in the base, much nicer than fussing with shims forever more! (Edit: I just mic'd the height of the groove base on mine, and milled my step to that size. You could make the clamp a fraction taller so it's gripping on the inside first, and any flex in the clamp means you are transferring force outwards, rather than starting with an outboard downforce to begin with. Did that make any sense?)

    Your table must be a slightly different design to mine (a 6" vertex), mine's got two open slots, or ears, one on the left and one on the right, and so for me it's much like holding down a standard mill vise.

    Good luck with your build!

    Craig
    Last edited by craig9; Jul 28, 2020 at 12:08 PM. Reason: clarity

  10. #9
    Supporting Member Crusty's Avatar
    Join Date
    May 2019
    Location
    Dry Gulch, Tx
    Posts
    749
    Thanks
    220
    Thanked 845 Times in 324 Posts

    Crusty's Tools
    I used Thompson QS shaft and I made a D reamer of that same shaft to ream the holes in the vise and smoothed with emery cloth on a wooden dowel. Since there's normally very little movement I didn't think that bushings were necessary. That particular shaft is hard enough to be durable but not too difficult to machine if you take it easy.

    I just took a look and realized that I'd forgotten that I had to offset the rotary table to the edge of my milling table because of the dividing plate, so that clamp idea may be a bust.



    186 More Best Homemade Tools eBook
    If you can't make it precise make it adjustable.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •