Remove advertisements
Results 1 to 7 of 7
  1. #1
    jere's Avatar
    Join Date
    Feb 2015
    Posts
    200
    Thanks
    183
    Thanked 111 Times in 69 Posts

    Some ideas for heat shrink tube

    Some ideas for heat shrink tube-20150808_145604.jpg

    a while back I bought some assorted size heat shrink tubing from harbor freight. some of it was much larger diameter than I could use. so I have found it works well for adding pocket could to flashlights and pens that have had the originals snap off or just didn't come with clips. it also works to add keychains or loops to stuff you might want to hang up.

    for all of the above I dipped the object in contact cement or used hot glued to keep the shrink tube from sliding off. for the key chain ends I think the tubingng and clamped the open end in a vise while still hot. then punched a hole in the shrink tube after it cooled. pretty simple cheap idea that could work for a lot of different things so hopefully some one else can use this idea too.

    if anyone else has some uses for heat shrink tube please share as wellSome ideas for heat shrink tube-20150808_145547.jpg
    Last edited by jere; 08-11-2015 at 03:10 PM.

  2. The Following 13 Users Say Thank You to jere For This Useful Post:

    Altair (08-23-2015), grandviewdoug (11-19-2017), Grumpyoldman (02-16-2016), gustave (02-29-2016), j.bickley (11-18-2017), Jon (08-11-2015), kbalch (08-11-2015), lazarus (07-11-2016), Paul Jones (08-12-2015), PJs (08-12-2015), rlm98253 (11-18-2017), Toolmaker51 (11-18-2017), WoodChip (02-06-2016)

  3. #2
    PJs
    PJs is offline
    PJs's Avatar
    Join Date
    Sep 2014
    Location
    Northern CA
    Posts
    673
    Thanks
    3,150
    Thanked 568 Times in 352 Posts
    Thanks Jere...amazing stuff...like velcro. I recently used it on the shower curtain rings because I got tired of the SQUEAL every time the curtain moves. Just cut some pieces to length, shrunk'em...and Whalah...no more SQUEALCH. Thanks for the ideas of other uses!
    ‘‘When you are in it up to your ears, keep your mouth shut’’ Anonymous ~PJ

  4. The Following 2 Users Say Thank You to PJs For This Useful Post:

    jere (08-12-2015), Paul Jones (08-12-2015)

  5. #3
    Content Editor Altair's Avatar
    Join Date
    Aug 2013
    Posts
    667
    Thanks
    119
    Thanked 80 Times in 68 Posts
    Thanks for the tip, jere. Reminds me to put some on my tools, I'm cursed with sweaty hands.

    Al

  6. The Following User Says Thank You to Altair For This Useful Post:

    jere (08-24-2015)

  7. #4
    Content Editor DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,059
    Thanks
    250
    Thanked 464 Times in 418 Posts
    Never thought of that application for heat shrink tubing, jere. Thanks for the idea.

  8. The Following User Says Thank You to DIYer For This Useful Post:

    rlm98253 (11-18-2017)

  9. #5
    Raven Sirius's Avatar
    Join Date
    Mar 2015
    Posts
    7
    Thanks
    4
    Thanked 3 Times in 1 Post
    I LOVE HEAT SHRINK!

    You know when you lose the aglet of your lace and it frays, then you can't put your shoes on properly, then fall on your face because your laces are all over the place. I don't! I've never had that happen because the very first time I saw heat shrink I went and bought metres long lengths of it. Then went home and fixed the end of all my shoelaces!

    Over the years the only development to this process is now before I carefully shrink the heat shrink I squirt in a few drops of Gorilla brand super glue. This process will even double the lifespan of long boot laces that have frayed from rubbing against metal eyes. Just slide the HS down to cover the fray, and then some, squirt in the glue at either end, do not burn the lace in two... voila! Just make sure the lace is not copmpletely severed though, this process will not 'repair' a lace.

  10. The Following 3 Users Say Thank You to Raven Sirius For This Useful Post:

    lazarus (07-11-2016), PJs (01-25-2016), WoodChip (02-06-2016)

  11. #6

    Join Date
    May 2013
    Posts
    23
    Thanks
    20
    Thanked 5 Times in 5 Posts
    [QUOTE=jere;28841]

    if anyone else has some uses for heat shrink tube please share as well

    I've been using some for shoestring aglet replacements.
    ---Joe

  12. #7
    Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    615
    Thanks
    1,392
    Thanked 517 Times in 313 Posts
    I replaced broken off plastic tips of eyeglass temples [part that rests on ears].
    Lots of shoelace tips too.
    Covered screwdriver shanks, while not suitable for high voltage, made 12v auto work easier.
    Have put short bands on other tools to ID special sizes, especially hex wrenches.
    Put longer tubes, 1 1/2" long or so, on far end of thin machinists scales to help pick them up. In electronic assembly, non-conductive finger cots or gloves made picking up a scale sort of impossible, by 'masking' your finger nail.
    By same token, used heat shrink on fiberglass probes and potentiometer adjusters. Find a hex nut that slip fits on shaft, lock in place with heat shrink.
    Also tried as a spacer on shafts of a import rock tumbler, to keep worn tires in place. Worked so-so, made set screw collars; worked 100%.


    Post your reply!
    Join 20,941 of us and get our 50 Must Read Homemade Tools eBook free.



    50 Must Read Homemade Tools
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  13. The Following User Says Thank You to Toolmaker51 For This Useful Post:

    Paul Jones (11-20-2017)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •