Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Results 1 to 7 of 7

Thread: Rear Tool Post Spacer Block Sherline Lathe

  1. #1
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools

    Rear Tool Post Spacer Block Sherline Lathe

    They say the Sherline Lathe is at it's best with a rear cutoff tool and I always wanted to try that on my mini lathe.
    So, I made a spacer block for the Sherline supplied front cutoff tool and got a longer hold down bolt for use on the rear of the cross slide table.
    Nothing special about this at all, just a 1/2" high block of aluminum with a hole in the right place. It is not in the center but offset.

    We won't know how this works for a while.
    Attached Thumbnails Attached Thumbnails Rear Tool Post Spacer Block Sherline Lathe-img_1954b-copy.jpg  

    186 More Best Homemade Tools eBook

  2. The Following 6 Users Say Thank You to jjr2001 For This Useful Post:

    Jon (Apr 28, 2018), olderdan (Apr 28, 2018), Paul Jones (Apr 28, 2018), PJs (Apr 30, 2018), rossbotics (Apr 28, 2018), Seedtick (Apr 28, 2018)

  3. #2
    Supporting Member rossbotics's Avatar
    Join Date
    Dec 2013
    Location
    Florida
    Posts
    730
    Thanks
    1,019
    Thanked 1,639 Times in 402 Posts

    rossbotics's Tools
    Lots of smaller machines with the cutoff tool mounted in reverse works better than the conventional method, eliminating chatter

    2000 Tool Plans
    Comments are always welcome
    Doug

    Subscribe to my you tube channel

    https://www.youtube.com/channel/UCDD..._as=subscriber



    Tool Plans for Sale by rossbotics






  4. The Following User Says Thank You to rossbotics For This Useful Post:

    jjr2001 (Apr 29, 2018)

  5. #3
    Supporting Member olderdan's Avatar
    Join Date
    Jun 2016
    Posts
    781
    Thanks
    1,456
    Thanked 1,531 Times in 463 Posts

    olderdan's Tools
    That should be a great improvement that set up works for me on my SB, is the reverse position just for the photo shoot?.

  6. The Following User Says Thank You to olderdan For This Useful Post:

    jjr2001 (Apr 29, 2018)

  7. #4
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools
    I hope to have some material ready for my next model engine soon and then we will see how well it works on the Sherline.
    Cheers, JR

  8. #5
    Supporting Member tonyfoale's Avatar
    Join Date
    Nov 2016
    Location
    Spain
    Posts
    1,549
    Thanks
    679
    Thanked 2,627 Times in 705 Posts

    tonyfoale's Tools
    I have a rear mounted tool post and I find parting to work about the same as when using the front one. No advantage nor disadvantage. I also have a 4 way indexable tool holder on that rear post which always has 3 tools mounted, 1. the parting tool, 2. a small drill chuck with a short spotting drill bit and a normal turning tool.
    The advantage that I find with the rear tool post is that I don't have to change tools on the front one as often and the permanently mounted spotting drill saves quite a few tailstock chuck and/or drill bit changes. Unless actually drilling for a centre I prefer a spotting drill to a centre drill for a pilot hole.
    Sometimes the rear post gets in the way on certain jobs but I made it to be removable quickly and I machined register surfaces so that it goes back into the same place when fitted again. I don't have to take it off often.

  9. The Following User Says Thank You to tonyfoale For This Useful Post:

    jjr2001 (Apr 30, 2018)

  10. #6
    Supporting Member jjr2001's Avatar
    Join Date
    Jun 2016
    Posts
    915
    Thanks
    1,182
    Thanked 2,044 Times in 553 Posts

    jjr2001's Tools
    Thanks for the info Tony, I did not think to put a 3 or 4 way tool holder back there. Could bring some extra versatility to the lathe.

    Cheers, JR

  11. #7
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,056
    Thanks
    772
    Thanked 1,850 Times in 1,652 Posts


    Thanks jjr2001! We've added your Rear Tool Post Spacer to our Lathe Accessories category,
    as well as to your builder page: jjr2001's Homemade Tools. Your receipt:






    186 More Best Homemade Tools eBook

  12. The Following User Says Thank You to DIYer For This Useful Post:

    jjr2001 (May 1, 2018)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •