Free 186 More Best Homemade Tools eBook:  
New: 300+ fresh build posts/day from 275 forums → BuildThreads.com

Clutch

Because I have dementia I need to breakdown projects into small components. Completed a a clutch that could be used anywhere power via a fan belt needs a clutch. Hope my comments regarding each photo are attached....

  1. members/gord/albums/clutch/5842-dsc5742-copy-assembled-tested-ready-go.jpg

  2. members/gord/albums/clutch/5843-dsc5741-copy-support-shaft-i-machined-pipe-mount-bearing-press-fit-but-i-threaded-set-screw-well-welded-back-mounting-plate-tested-trueness-micrometer-ran-1725-rpm-without-any-vibration-expect-normal-speed-60-120-rpm-what-my-use-will.jpg

  3. members/gord/albums/clutch/5844-dsc5740-copy-final-length-shaft-will-determined-what-type-coupling-i-will-make-connect-drive-motor.jpg

  4. members/gord/albums/clutch/5841-dsc5738-copy-cut-key-way-one-two-bearing-mounted-shaft-used-stack-3-cutting-discs-mandrel-cut-key-way.jpg

  5. members/gord/albums/clutch/5840-dsc5735-copy-originally-going-reuse-old-crank-shaft-but-decided-build-anew-compressors-shaft-has-straight-cut-key-way-outer-plate-many-smaller-cars-i-understand-have-tapered-shaft-so-making-new-one-very-easy-turned-end-down-fit-pulley-then-cut-key-way-old-one-externally-threaded-5-16-nuts-i-just-reversed-drilled-tapped-5-16-hole-there-enough-meat-key-way-would-cut-into-tapped-hole.jpg

  6. members/gord/albums/clutch/5839-dsc5739-copy-both-clutch-plates-had-rust-pits-bumps-made-creep-little-under-no-load-so-put-them-lathe-took-just-enough-off-remove-scale-bumps-not-affect-clutch-plate-clutch-plate-clearance-disengaged-mod.jpg

  7. members/gord/albums/clutch/5838-dsc5726-copy-just-perspective-here-outside-clutch-plate.jpg

  8. members/gord/albums/clutch/5837-dsc5725-copy-just-perspective-here-inside-clutch-plate.jpg

  9. members/gord/albums/clutch/5836-dsc5724-copy-just-perspective-here-magnetic-coil-front-plate.jpg

  10. members/gord/albums/clutch/5835-dsc5729-copy-steel-collar-set-into-hole-where-main-shaft-goes-has-o-ring-around-neither-required-punched-out-clutch-side-plate.jpg

  11. members/gord/albums/clutch/5834-dsc5723-copy-lathed-backside-plate-flat-so-will-bolt-tight-mounting-bracket-later.jpg

  12. members/gord/albums/clutch/5833-dsc5722-copy-i-lathed-plate-round-help-balance-out-further-lathing-bearings-lost-material-around-two-bolt-holes-but-other-4-more-then-enough-hold.jpg

  13. members/gord/albums/clutch/5832-dsc5721-copy-here-cover-ac-compressor-off-larger-vehicle-hoses-out-were-about-1-inch-diameter-give-u-idea-size-pump.jpg
Showing photos 1 to 13 of 13