Free 186 More Best Homemade Tools eBook:  
Get 2,000+ tool plans, full site access, and more.

User Tag List

Page 4 of 5 FirstFirst 1 2 3 4 5 LastLast
Results 31 to 40 of 43

Thread: Pull Start Tool for Mower, Washer, Saw, Stimmer etc

  1. #31
    Supporting Member gunsgt1863's Avatar
    Join Date
    Oct 2013
    Location
    SE Wisconsin
    Posts
    29
    Thanks
    283
    Thanked 19 Times in 8 Posts
    Quote Originally Posted by brankif View Post
    All, still only 61 tickets sold for the raffle donating to the World Heart Federation...those aren't bad odds.
    Quick link to raffle site is :

    https://rafflecreator.com/pages/pull-starter
    brankif, the link is not working.

    186 More Best Homemade Tools eBook

  2. #32

    Join Date
    Oct 2012
    Location
    Erie, PA
    Posts
    103
    Thanks
    261
    Thanked 35 Times in 26 Posts
    I use that same setup for my 4000 watt Champion Generator. When I converted it to Natural Gas it took a while to get the gas flow dialed in right and I was getting tired of pulling on that darn pull start cord. The drill did the work and I made the flow adjustments with it spinning until it fired up. Turns out the suggested starting point for the gas flow was quite a bit off. I would have worn out my shoulder getting there.
    My Craftsman weed Whacker came stock with a similar setup, although I never had to use, it. It always started good.

    2000 Tool Plans

  3. #33

    Join Date
    Apr 2017
    Posts
    5
    Thanks
    0
    Thanked 7 Times in 2 Posts

    Dirtinla's Tools
    Where there is a will there's a way... check this out

    https://www.instructables.com/id/Ste...Assist-for-Th/

  4. #34

    Join Date
    Jan 2016
    Posts
    5
    Thanks
    0
    Thanked 1 Time in 1 Post
    So - the bottom line is still that this is a great idea. It would be great if the guy is not going to sell them, then he could at least offer the plans for sale - seems there is sufficient interest from the community to build some - maybe make some upgrades - and for the creator to make a buck. Its been several years since this idea surfaced, some one should be interested in making these.
    IMHO

  5. The Following User Says Thank You to rsoby For This Useful Post:

    Sleykin (May 2, 2018)

  6. #35

    Join Date
    Apr 2016
    Posts
    1
    Thanks
    1
    Thanked 2 Times in 1 Post

  7. The Following 2 Users Say Thank You to pecinjo For This Useful Post:

    Jon (Dec 13, 2017), Trojan Horse (Dec 16, 2017)

  8. #36

    Join Date
    Apr 2017
    Posts
    5
    Thanks
    0
    Thanked 7 Times in 2 Posts

    Dirtinla's Tools
    Since Mr Brankif hasn't surfaced and it seems like there is a ton of interest I will post this which I found in common domain on the web.

    I didn't really understand it but perhaps the DIY'ers out there can simplify.

    Mr Brankif I do apologize if you did not want this information out there.


    https://patentimages.storage.googlea...50252769A1.pdf

  9. The Following 4 Users Say Thank You to Dirtinla For This Useful Post:

    Jon (Dec 13, 2017), pecinjo (Dec 13, 2017), Trojan Horse (Dec 16, 2017), yves78 (May 3, 2018)

  10. #37

    Join Date
    Nov 2015
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I've tried this way myself! The fatal problem I had was turning the engine in the wrong direction after removing the complete puller cover. Be careful, I snapped the nut right off the end of the crank. Game over!! Learning the hard way...

  11. #38
    Karl7's Avatar
    Join Date
    Dec 2017
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Nice Job!
    You are a Sharp guy.
    Proverbs 27:17
    As Iron sharpens iron so one man sharpens another

    Thanks

  12. #39

    Join Date
    Apr 2015
    Posts
    18
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi, There seems to be a video but for some reason it show up with a black
    screen and no video. What gives? those anyone know why.

  13. #40
    Supporting Member
    Join Date
    Nov 2017
    Location
    Kaslo, BC, Canada
    Posts
    30
    Thanks
    1
    Thanked 5 Times in 5 Posts
    A super tool, brankif, but is it, or the plans for it, available? I know it's some time since your original posting showing it in action, and I assume the raffle has finished. At only 61 tickets sold by the time of your last post, it seems unlikely that you were able to make a significant donation to the World Heart Federation. Perhaps one reason for a low level of interest is that you don't state your location in your profile, and since HMT has a truely international membership many may have been put off by possible freight and customs duty concerns.

    However, have you thought about selling plans for your machine on HMT? I would certainly be interested in buying a set, as I'm sure many other members would. This has the potential for significant fund raising.

    Mike

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •