Free 173 Best Homemade Tools eBook:  
Get 500+ homemade tool plans, tool build guides, ebooks, and much more.

Tab Content
  • th62's Avatar
    07-10-2020, 03:42 AM
    th62 started a thread Panel hammer. in Homemade Tools
    Panel beating time. Going to attempt to straighten the bent and buckled TX650 guards with this Delrin hammer I turned up today. I knew this ball...
    1 replies | 651 view(s)
  • th62's Avatar
    06-18-2020, 03:13 AM
    No comment
    10 replies | 1807 view(s)
  • th62's Avatar
    06-18-2020, 03:04 AM
    th62 replied to a thread XS65 barn find. in Wheels
    Here's a video of the first engine start up and another of the homemade manometer in use. I've since made a better, neater looking manometer, but...
    1 replies | 134 view(s)
  • th62's Avatar
    06-18-2020, 02:25 AM
    th62 started a thread XS65 barn find. in Wheels
    This is an XS650 Yamaha I bought as a non runner a while back. Mostly just a pile of rust, all fixings were binned along with seat, mudguard,...
    1 replies | 134 view(s)
  • th62's Avatar
    06-18-2020, 01:42 AM
    th62 started a thread Bowl lathe. in Homemade Creations
    This is a bowl turning lathe I made up many, many years ago. It had six speeds via the multi speed pulleys I turned up on my AL-300 metal lathe, the...
    2 replies | 647 view(s)
  • th62's Avatar
    06-18-2020, 01:22 AM
    This is a canoe I rigged up for sailing many years ago. Canadian canoe was 16' long so I couldn't use a single sail as it would have been too tall...
    0 replies | 52 view(s)
  • th62's Avatar
    06-17-2020, 11:52 PM
    No comment
    10 replies | 1807 view(s)
  • th62's Avatar
    06-17-2020, 10:35 PM
    Read my previous comment!
    10 replies | 1807 view(s)
  • th62's Avatar
    06-17-2020, 09:06 PM
    Yep, here's some pics. I have three tables: One with a basic, flat table with angles scribed on top for freehand grinding sharpening, and another...
    4 replies | 2597 view(s)
  • th62's Avatar
    06-17-2020, 05:04 PM
    You're free to make it the way you like, I'll continue to actually make things the way they work best for me. Fair?
    10 replies | 1807 view(s)
  • th62's Avatar
    06-17-2020, 04:38 AM
    th62 replied to a thread Recumbent trike. in Wheels
    Some build pics.
    2 replies | 585 view(s)
  • th62's Avatar
    06-17-2020, 03:18 AM
    th62 started a thread Go carts. in Wheels
    A few of the gocarts I built over the years. I built about four for the kids using 125 Victa lawn mower engines. These created a few problems because...
    3 replies | 767 view(s)
  • th62's Avatar
    06-17-2020, 02:33 AM
    This is an optical centre punch I made some time ago. It's used for centre punching accurately, I added the LED light later. One is powered by a USB...
    10 replies | 1807 view(s)
  • th62's Avatar
    06-17-2020, 02:26 AM
    This is my final drill sharpening jig. Rather than spot bits of angle together, I used a piece of 25mm square bar, linished it, milled a V for the...
    4 replies | 2597 view(s)
  • th62's Avatar
    06-17-2020, 01:56 AM
    th62 started a thread Suzuki GS750 in Wheels
    Here's a little cutie, a bucket racer I built around the mid 80s. Itís a YB90 of early 70s vintage. I bought the bike for around $30 from memory and...
    0 replies | 73 view(s)
  • th62's Avatar
    06-17-2020, 01:54 AM
    th62 started a thread Yamaha Bucket Racer in Wheels
    Here's a little cutie, a bucket racer I built around the mid 80s. Itís a YB90 of early 70s vintage. I bought the bike for around $30 from memory and...
    0 replies | 84 view(s)
  • th62's Avatar
    06-17-2020, 01:49 AM
    th62 started a thread Triumph Bonny Hot Rod. in Wheels
    I can't ride bikes anymore as I can't use the levers and can't hang on while I kick them to life, wouldn't own a bike you couldn't kick. This is my...
    0 replies | 98 view(s)
  • th62's Avatar
    06-17-2020, 01:35 AM
    This is a rideon mower I built nearly 40 years ago. It was made from parts I scavenged from the local rubbish dump. The motor was a combination of...
    1 replies | 1383 view(s)
  • th62's Avatar
    06-15-2020, 03:25 AM
    th62 started a thread Recumbent trike. in Wheels
    Hereís my latest recumbent trike build, this is the 10th recumbent I've built. Suspension has nine evenly spaced settings and works really well,...
    2 replies | 585 view(s)
  • th62's Avatar
    06-15-2020, 02:55 AM
    Here's a new manometer I've just made. The top and bottom platforms consist of a neoprene gasket sandwiched between two pieces of ply, the inner...
    1 replies | 1238 view(s)
No More Results
About th62

Basic Information

About th62
Homemade Tools Builder Page:

Statistics


Total Posts
Total Posts
39
Posts Per Day
0.02
Total Thanks
Total Thanks
0
  • Thanked 145 Times in 21 Posts
General Information
Last Activity
Today 01:46 AM
Join Date
10-08-2015
No results to display...
No results to display...

06-17-2020


Awards Showcase - 2 Awards

Icon Image Description
Supporting Member Supporting Member Name: Supporting Member
This award is given to supporting forum members who receive access to an exclusive Supporters forum with homemade tool build guides, eBooks, tool plans, and premium supporter-only content. Click here to subscribe.
Issue time: 10-13-2019, 12:35 PM
Issue reason: Thanks for your support of HomemadeTools.net! You can now access our exclusive Supporters forum.
10 Posts 10 Posts Name: 10 Posts
This award is given to members who have contributed at least 10 posts on the Homemade Tools forum.
Issue time: 11-21-2017, 12:30 AM
Issue reason: This award is given to members who have contributed at least 10 posts on the Homemade Tools Forum.